HORNER XLE-Model 2 Instructions

Page 9
SAFETY & MAINTENANCE
Warnings
1.
Toavoidtheriskofelectricshockorburns,alwayscon-
nectthesafety(orearth)groundbeforemakinganyother
connections.
2.
Toreducetheriskoffire,electricalshock,orphysical
injury,itisstronglyrecommendedtofusethevoltage
measurementinputs.Besuretolocatefusesascloseto
thesourceaspossible.
3.
Replacefusewiththesametypeandratingtoprovidepro-
tectionagainstriskoffireandshockhazards.
4.
Intheeventofrepeatedfailure,doNOTreplacethefuse
againasrepeatedfailureindicatesadefectivecondition
thatwillNOTclearbyreplacingthefuse.
5.
Onlyqualifiedelectricalpersonnelfamiliarwiththecon-
structionandoperationofthisequipmentandthehazards
involvedshouldinstall,adjust,operate,orservicethis
equipment.
6.
Readandunderstandthismanualandotherapplicable
manualsintheirentiretybeforeproceeding.Failureto
observethisprecautioncouldresultinseverebodilyinjury
orlossoflife.
7.
WARNING-Batterymayexplodeifmistreated.Donot
recharge,disassemble,ordisposeofinfire.
8.
WARNING - EXPLOSION HAZARD-Batteriesmustonly
bechangedinanareaknowntobenon-hazardous.
9.
WARNING-Donotdisconnectwhilecircuitisliveunless
areisknowtobenon-hazardous.

FCC Compliance
ThisdevicecomplieswithPart15oftheFCCRules.Operationis
subjecttothefollowing
twoconditions:
1.
Thisdevicemaynotcauseharmfulinterference.
2.
Thisdevicemustacceptanyinterferencereceived,includ-
inginterferencethatmaycauseundesiredoperation.


Technical Support
North America
1(317)916-4274
(877)665-5666
www.hornerautomation.com
techsppt@heapg.com

Europe
+353(21)4321-266
www.hornerautomation.eu
technical.support@horner-apg.com



Precautions
Allapplicablecodesandstandardsneedtobefollowedinthe
installationofthisproduct.Adheretothefollowingsafetypre-
cautionswheneveranytypeofconnectionismadetothemodule:
1.
Connectthesafety(earth)groundonthepowerconnector
firstbeforemakingany
2.
otherconnections.
3.
Whenconnectingtotheelectriccircuitsorpulse-initiating
equipment,opentheir
4.
relatedbreakers.
5.
DoNOTmakeconnectiontolivepowerlines.
6.
Makeconnectionstothemodulefirst;thenconnecttothe
circuittobemonitored.
7.
Routepowerwiresinasafemannerinaccordancewith
goodpracticeandlocalcodes.
8.
Wearproperpersonalprotectiveequipmentincluding
safetyglassesandinsulatedgloveswhenmakingcon-
nectionstopowercircuits.
9.
Ensurehands,shoes,andflooraredrybeforemakingany
connectiontoapowerline.
10.
MakesuretheunitisturnedOFFbeforemakingcon-
nectiontoterminals.
11.
Makesureallcircuitsarede-energizedbeforemakingcon-
nections.
12.
Beforeeachuse,inspectallcablesforbreaksorcracksin
theinsulation.Replace
13.
immediatelyifdefective.
14.
UsecopperconductorsinFieldWiringonly,60/75˚C.
15.
UsecautionwhenconnectingcontrollerstoPCsviaserial
orUSB.PCs,especiallylaptops,mayuse“floatingpower
supplies”thatareungrounded.Thiscouldcauseadam-
agingvoltagepotentialbetweenthelaptopandcontroller.
Ensurethecontrollerandlaptoparegroundedformax-
imumprotection.ConsiderusingaUSBisolatordueto
voltagepotentialdifferencesasapreventativemeasure.



HORNER XLE-Model 2 Specifications

General

Brand	HORNER
Model	XLE-Model 2
Category	Controller
Language	English