HP XP P9500

DKA145 - - - - - - 30009 145
DKA146 URA URA_000 CL1-H 0 2 0 30009 146
DKA147 URA URA_001 CL1-H 0 3 0 30009 147
DKA148 URA URA_002 CL1-H 0 4 0 30009 148
DKA149 URA URA_003 CL1-H 0 5 0 30009 149
DKA150 URA URA_004 CL1-H 0 6 0 30009 150
HORCM Shutdown inst 9 !!!
Please check 'SYS$SYSROOT:[SYSMGR]HORCM9.CONF','SYS$SYSROOT:[SYSMGR.LOG9.CURLOG]
HORCM_*.LOG', and modify 'ip_address & service'.
HORCM inst 9 finished successfully.
$SYS$SYSROOT:[SYSMGR]horcm9.conf (/sys$sysroot/sysmgr/horcm9.conf)
# Created by mkconf on Thu Mar 13 20:08:41
HORCM_MON
#ip_address service poll(10ms) timeout(10ms)
127.0.0.1 52323 1000 3000
HORCM_CMD
#dev_name dev_name dev_name
#UnitID 0 (Serial# 30009)
DKA145
# ERROR [CMDDEV] DKA145 SER = 30009 LDEV = 145 [ OPEN-9-CM `
HORCM_DEV
#dev_group dev_name port# TargetID LU# MU#
# DKA146 SER = 30009 LDEV = 146 [ FIBRE FCTBL = 3 ]
URA URA_000 CL1-H 0 2 0
# DKA147 SER = 30009 LDEV = 147 [ FIBRE FCTBL = 3 ]
URA URA_001 CL1-H 0 3 0
# DKA148 SER = 30009 LDEV = 148 [ FIBRE FCTBL = 3 ]
URA URA_002 CL1-H 0 4 0
# DKA149 SER = 30009 LDEV = 149 [ FIBRE FCTBL = 3 ]
URA URA_003 CL1-H 0 5 0
# DKA150 SER = 30009 LDEV = 150 [ FIBRE FCTBL = 3 ]
URA URA_004 CL1-H 0 6 0
HORCM_INST
#dev_group ip_address service
URA 127.0.0.1 52323
(7) Using $1$* naming as native device name.
You can use the native device without DEFINE/SYSTEM command by specifying $1$* naming
directly.
$ inqraid $1$DGA145-155 -CLI
DEVICE_FILE PORT SERIAL LDEV CTG H/M/12 SSID R:Group PRODUCT_ID
$1$DGA145 CL2-H 30009 145 - - - - OPEN-9-CM
$1$DGA146 CL2-H 30009 146 - s/P/ss 0004 5:01-11 OPEN-9
$1$DGA147 CL2-H 30009 147 - s/S/ss 0004 5:01-11 OPEN-9
$1$DGA148 CL2-H 30009 148 0 P/s/ss 0004 5:01-11 OPEN-9
$ pipe show device | INQRAID -CLI
DEVICE_FILE PORT SERIAL LDEV CTG H/M/12 SSID R:Group PRODUCT_ID
$1$DGA145 CL2-H 30009 145 - - - - OPEN-9-CM
$1$DGA146 CL2-H 30009 146 - s/P/ss 0004 5:01-11 OPEN-9
$1$DGA147 CL2-H 30009 147 - s/S/ss 0004 5:01-11 OPEN-9
$1$DGA148 CL2-H 30009 148 0 P/s/ss 0004 5:01-11 OPEN-9
$ pipe show device | MKCONF -g URA -i 9
starting HORCM inst 9
HORCM Shutdown inst 9 !!!
A CONFIG file was successfully completed.
HORCM inst 9 finished successfully.
starting HORCM inst 9
DEVICE_FILE Group PairVol PORT TARG LUN M SERIAL LDEV
$1$DGA145 - - - - - - 30009 145
$1$DGA146 URA URA_000 CL2-H 0 2 0 30009 146
$1$DGA147 URA URA_001 CL2-H 0 3 0 30009 147
$1$DGA148 URA URA_002 CL2-H 0 4 0 30009 148
HORCM Shutdown inst 9 !!!
Please check 'SYS$SYSROOT:[SYSMGR]HORCM9.CONF','SYS$SYSROOT:[SYSMGR.LOG9.CURLOG]
HORCM_*.LOG', and modify 'ip_address & service'.
HORCM inst 9 finished successfully.
$
$ pipe show device | RAIDSCAN -find
DEVICE_FILE UID S/F PORT TARG LUN SERIAL LDEV PRODUCT_ID
$1$DGA145 0 F CL2-H 0 1 30009 145 OPEN-9-CM
$1$DGA146 0 F CL2-H 0 2 30009 146 OPEN-9
Porting notice for OpenVMS 27