HPE BladeSystem c7000 User Manual

14
•
Remote deployment installation—Use Insight Control server
deployment for an automated solution to remotely deploy an
operating system.
For additional system software and firmware updates, download the
Service Pack for ProLiant (SPP) from the Hewlett Packard
Enterprise website (http://www.hpe.com/servers/spp/download).
The Smart Update Firmware DVD ISO is also available at the
download tab on the Hewlett Packard Enterprise website
(http://www.hpe.com/info/foundation).
For information on using these installation methods, see the Hewlett
Packard Enterprise website (http://www.hpe.com/info/ilo/docs).
Installing the operating system for
G7 servers
To operate properly, the server must have a supported operating
system installed. For the latest information on supported operating
systems, see the Hewlett Packard Enterprise website
(http://www.hpe.com/info/supportos).
Methods to install an operating system on the server include:
•
SmartStart assisted installation—Insert the SmartStart CD into
the DVD-ROM drive and reboot the server.
•
Manual installation—Insert the operating system CD into the
DVD-ROM drive and reboot the server. You might have to
obtain additional drivers and firmware from the SPP download
site (http://www.hpe.com/servers/spp/download).
For more information, download the Service Pack for ProLiant (SPP)
from the Hewlett Packard Enterprise website
(http://www.hpe.com/servers/spp/download).
Troubleshooting resources
The BladeSystem c-Class Enclosure Troubleshooting Guide
provides procedures and solutions for troubleshooting BladeSystem
c-Class enclosures. This guide explains how to use the Insight
Display to troubleshoot enclosures, and it includes a flowchart to
help you navigate the troubleshooting process. To view the guide,
see the Hewlett Packard Enterprise website
(http://www.hpe.com/support/BladeSystem_Enclosure_TSG_en).
Before contacting Hewlett Packard Enterprise Technical Support, be
sure to have an Onboard Administrator Show All report available.
Hewlett Packard Enterprise Technical Support must analyze the
Onboard Administrator Show All report for configuration errors
before proceeding. For instructions on how to create an Onboard
Administrator Show All report, see the Hewlett Packard Enterprise
website (http://www.hpe.com/info/BladeSystemOA-ShowAll).
For more information
Refer to the Hewlett Packard Enterprise website
(http://www.hpe.com/info/bladesystem/docs) for more detailed setup
and configuration information as well as regulatory, safety, and
environmental notices. This information can be found in the
BladeSystem c-Class Solution Overview and the BladeSystem
c7000 Enclosure Setup and Installation Guide.
Documentation feedback
Hewlett Packard Enterprise is committed to providing documentation
that meets your needs. To help us improve the documentation, send
any errors, suggestions, or comments to Documentation Feedback
(mailto:docsfeedback@hpe.com). When
submitting your feedback,
include the document title, part number, edition, and publication date
located on the front cover of the document. For online help content,
include the product name, product version, help edition, and
publication date located on the legal notices page.

HPE BladeSystem c7000 Specifications

General

Form Factor	10U
Interconnect Bays	8
Blade Slots	16 half-height or 8 full-height
Device Bays	16 half-height blade server bays or 8 full-height blade server bays
Power Supplies	Up to 6 hot-plug power supplies
Cooling Fans	10 hot-plug fans
Management	Onboard Administrator
Height	17.5 inches
Width	17.6 inches
Compatibility	HPE ProLiant and Integrity server blades
Non-operating Temperature	-40° to 70°C (-40° to 158°F)
Operating Humidity	10% to 90% (non-condensing)
Non-operating Humidity	5% to 95% (non-condensing)
Networking	Dependent on installed interconnect modules
Operating Temperature	10° to 35°C (50° to 95°F)