What to do if the Huawei SUN2000-8KTL-M0 Inverter Upgrade Failed or Software Version Unmatch?
If your Huawei Inverter displays 'Upgrade Failed or Software Version Unmatch,' it means the upgrade process did not complete successfully. To resolve this: 1. Try performing the upgrade again. 2. If the upgrade fails multiple times, contact your dealer or Huawei technical support.
Why does my Huawei SUN2000-8KTL-M0 show Abnormal Grounding and how do I fix it?
If your Huawei Inverter displays an 'Abnormal Grounding' error, it indicates that the N cable or ground cable is not connected, especially when a PV array is grounded and the inverter output isn't connected to an isolation transformer. To resolve this: * Power off the inverter and check the PE cable connection. * If connected to a TN power grid, verify the N cable connection and its voltage to ground. * If the output is connected to an isolation transformer, disable Grounding inspection via the mobile app, SmartLogger, or NMS.
What causes DC Arc Fault in Huawei SUN2000-8KTL-M0 Inverter?
A 'DC Arc Fault' error on your Huawei Inverter means the PV string power cable is arcing or has a poor connection. Check whether the string cables arc or are in poor contact.
How to troubleshoot High String Input Voltage on Huawei SUN2000-8KTL-M0 Inverter?
A 'High String Input Voltage' error on your Huawei SUN2000 Inverter indicates that too many PV modules are connected in series, causing the open-circuit voltage to exceed the inverter's maximum input voltage. To solve this, check the number of PV modules connected in series and ensure the PV string open-circuit voltage is within the inverter's maximum operating voltage. After correcting the PV array configuration, the alarm should disappear automatically.
What causes Low Insulation Resistance in Huawei Inverter and how to fix it?
If your Huawei Inverter is showing a 'Low Insulation Resistance' error, it means that the PV arrays are short-circuited with PE, or the ambient air of the PV array is damp, leading to poor insulation between the PV array and the ground. Here's how to address it: 1. Check the output resistance of the PV array to ground. Rectify any short circuits or insulation issues. 2. Ensure the PE cable of the SUN2000 is correctly connected. 3. If the low impedance persists in cloudy or rainy conditions, log in to the mobile app, SmartLogger, or NMS to reset the insulation impedance protection threshold.
How to fix String Reversed error on Huawei Inverter?
If your Huawei Inverter displays a 'String Reversed' error, it means the PV string is reversely connected. To fix this, wait until night when solar irradiance declines and the PV string current drops below 0.5 A. Then, set the DC SWITCH to the OFF position and correct the string polarity.
What to do if my Huawei SUN2000-8KTL-M0 shows a Grid Failure?
If your Huawei Inverter reports a grid failure, it means that the power grid has experienced an outage, the AC circuit is disconnected, or the AC switch is off. To resolve this, first, check the AC voltage. Second, check whether the AC circuit is disconnected or the AC switch is off.
How to fix Low Insulation Resistance on Huawei SUN2000-8KTL-M0?
If your Huawei Inverter displays a 'Low Insulation Resistance' error, it could be due to the PV array being short-circuited to ground or the power cable not being well insulated, especially in a moist environment. Here's what you should do: * Check the impedance between the PV array output and PE, and eliminate any short circuits or points of poor insulation. * Ensure the PE cable for the inverter is correctly connected. * If you're certain the impedance is less than the preset protection threshold in cloudy or rainy conditions, you can log in to the mobile app, SmartLogger, or NMS to reset the insulation impedance protection threshold.
What to do if Huawei SUN2000-8KTL-M0 shows Grid Loss?
If your Huawei Inverter indicates a 'Grid Loss' error, it means the power grid might be experiencing an outage, or the AC power cable could be disconnected, or the AC circuit breaker is OFF. To resolve this, first, verify that the AC voltage is normal. Second, ensure that the AC power cable is properly connected and the AC switch is in the ON position.
General| Model | SUN2000-8KTL-M0 |
|---|---|
| Rated Output Power | 8000 W |
| Max. DC Voltage | 1100 V |
| Maximum DC Input Voltage | 1100 V |
| Start Voltage | 200 V |
| Number of MPPTs | 2 |
| Rated Grid Frequency | 50 Hz / 60 Hz |
| Max Efficiency | 98.6% |
| Weight | 17 kg |
| Cooling Method | Natural Convection |
| Protection Degree | IP65 |
| Protection Class | Class I |
| Cooling | Natural Convection |
| Protection Level | IP65 |
| Max. AC Power | 8800 VA |
| Maximum AC Output Power | 8800 VA |
| Rated AC Voltage | 220 V / 380 V, 230 V / 400 V |
| Rated Grid Voltage | 220 Vac / 380 Vac, 230 Vac / 400 Vac |
| AC Voltage Range | 180-280 V |
| Dimensions (W x H x D) | 525 x 470 x 262 mm |
| Operating Temperature Range | -25°C to +60°C |
| Max. DC Power | 12000 W |
| Maximum DC Input Power | 12000 W |
To Next Page
