What to do if HunterDouglas Indoor Furnishing EasyRise cord tensioner has climbed to the headrail?
If the universal cord tensioner has climbed to the headrail, pull down on the spring to relieve tension and pull the universal cord tensioner to the bottom of the cord loop. Properly mount the cord tensioner, referring to the Universal Cord Tensioner Installation Instructions included with your HunterDouglas shading.
What to do if HunterDouglas Window Blinds UltraGlide clicks but doesn't lower?
If the lowering mechanism of your HunterDouglas UltraGlide blinds engages and clicks but the blind doesn't lower, the mechanism might be caught between raising and lowering functions. Try pulling the wand or cord vertically to slightly raise and reset the blind, then lower as usual.
How to fix HunterDouglas Window Blinds that don't raise or lower evenly?
If your HunterDouglas Window Blinds don't raise or lower evenly, check inside the headrail for any obstructions that might be preventing the mechanism from turning. Also, make sure the lift cords aren't pinched or tangled.
Why are my HunterDouglas Window Blinds hard to raise or lower?
If your HunterDouglas Window Blinds are hard to raise or lower, or won't move at all, and they're an inside mount, make sure the headrail is installed correctly. Shadings should not be forced into tight inside mount window openings.
Why HunterDouglas Indoor Furnishing EasyRise cord tensioner grabs onto the cord?
If the universal cord tensioner grabs onto the cord during operation, check that it is mounted properly. Reinstall it if necessary.
What to do if the bottom rail of my HunterDouglas Window Blinds with PowerView® Gen 3 doesn't raise or lower completely?
If the bottom rail of your HunterDouglas Window Blinds does not raise or lower completely, or its fully lowered position has changed, the batteries in the battery wand or satellite battery pack may be low. Try replacing the batteries. Also, make sure the power source is securely connected to the power cable and that the cables aren't pinched or caught in the headrail or installation brackets.
Why is my UltraGlide HunterDouglas Window Blind not lowering when I pull the cord?
If your UltraGlide HunterDouglas Window Blind will not lower when the wand or cord is pulled toward the center of the blind, the pull wand or cord must be in the fully retracted position to engage the lowering mechanism. Ensure the wand or cord is being pulled from the fully retracted position directly toward the center of the blind, and not down then over.
What to do if my HunterDouglas SimpleLift™ Window Blind makes a ratcheting noise?
If your SimpleLift™ HunterDouglas Window Blind makes a ratcheting noise while the center button is pushed in and the bottom rail is being raised, push harder on the center button. The button must be fully depressed to raise or lower the blind.
Why is my HunterDouglas Window Blinds PowerView Gen 3 not responding to the remote?
If your HunterDouglas Window Blinds with PowerView Gen 3 are not responding to the remote, first ensure the correct group number is selected on the remote. The LED for that group number should be lit. You can verify the shade's group number in the PowerView App. If that's not the issue, try replacing the remote's batteries.
Why HunterDouglas Window Blinds UltraGlide don't stay in place when raising?
If your HunterDouglas UltraGlide blinds don't stay in place as the wand or cord retracts during raising, it's likely that the lowering mechanism has been engaged. Make sure you're pulling down on the pull wand or cord, and not out or across the blind.
General| Material | High-quality fabrics, various options available |
|---|---|
| Light Filtering | Yes, varies by fabric selection |
| Privacy | Varies by shade/blind; from light filtering to room darkening |
| UV Protection | Yes, varies by fabric selection |
| Customization | Available in a wide range of fabrics, colors, and styles |
To Next Page
