How to fix 'Ear thermometer communication error' on Huntleigh SC300?
If the Huntleigh Monitor displays 'Ear thermometer communication error', it means the battery is too low or there is a problem with the communication module. Replace the battery and restart the monitor. If the error continues, contact service personnel.
What causes 'No pulse detected' on Huntleigh SC300 Monitor?
If the Huntleigh Monitor displays 'No pulse detected', it could be due to a probe being loose or faulty.
Why does Huntleigh SC300 show 'Diastolic pressure out of range'?
If the Huntleigh Monitor displays 'Diastolic pressure out of range', it means the measured value is outside the specified range. This can happen due to an incorrect patient group setting or using the wrong size cuff.
What causes 'Mean pressure out of range' on Huntleigh SC300 Monitor?
If the Huntleigh Monitor displays 'Mean pressure out of range', it means the measured value is outside the specified range. This can happen due to an incorrect patient group setting or using the wrong size cuff.
Why does my Huntleigh SC300 say 'Interference'?
If the Huntleigh Monitor displays 'Interference,' it means the signal is being affected by motion or noise. Check the area around the sensor for any sources of signal noise and ensure the patient isn't moving excessively.
What to do if Huntleigh SC300 Monitor displays 'Unrecognised probe'?
If your Huntleigh Monitor displays 'Unrecognised probe', it means that the sensor can’t be recognized by SpO2 module. Check the connection between probe and host, if the alarm still can’t be cancelled, contact service personnel or biomedical engineer.
How to fix 'NIBP weak signal' error on Huntleigh SC300 Monitor?
If the Huntleigh Monitor displays 'NIBP weak signal', it means that the cuff is loose or the signal is weak. Check the patient type setting and the connection, or replace the cuff. If the error continues, contact service personnel.
What to do if Huntleigh SC300 shows 'NIBP cuff type wrong'?
If the Huntleigh Monitor displays 'NIBP cuff type wrong', it means the cuff doesn’t match the patient type. Replace the cuff and measure again.
How to troubleshoot 'Air pressure Err' on Huntleigh SC300 Monitor?
If the Huntleigh Monitor displays 'Air pressure Err', it means the pressure is not stable, possibly due to hose entanglement. Check the connection or use a new cuff. If the problem continues, contact service personnel.
What does 'PI too low' mean on Huntleigh Monitor and how to fix it?
If your Huntleigh Monitor displays ‘PI too low’, it means the SpO2 signal is too weak. Check the patient’s condition and change the application site.
General| Type | Fetal Monitor |
|---|---|
| Model | SC300 |
| Manufacturer | Huntleigh |
| Display | LCD |
| Paper Speed | 1, 2, 3 cm/min |
| Parameters Monitored | Fetal Heart Rate, Uterine Contractions |
| Frequency Range/Ultrasound Frequency | 1 MHz |
| FHR1 Range | 30 – 240 bpm |
| FHR2 Range | 30 – 240 bpm |
| UC Range | 0 to 100 mmHg |
| TOCO Range | 0 to 100 mmHg |
Provides critical safety warnings and cautions for operating the monitor.
Identifies and explains the function of front panel controls and symbols.
Details the controls and connectors located on the rear panel of the monitor.
Identifies controls and optional components on the side panels.
Explains the meaning of various symbols and indicators used on the monitor.
Details the functions of the monitor's operational keys and buttons.
Explains how to connect the AC power cord to the monitor and a power outlet.
Details how to connect NIBP hoses, cuffs, and SpO2 sensors to the monitor.
Explains the power-on self-test process and what to verify.
Describes how to initiate and terminate NIBP measurements.
Explains how to configure and use automatic NIBP measurement intervals.
Guides on how to establish a wireless connection between the thermometer and monitor.
Details the procedure for taking a temperature measurement.
Introduces troubleshooting by explaining error codes and fault presentation.
Lists common errors and provides suggestions for correction.
Guides users on how to contact technical support and obtain service manuals.
To Next Page