Husqvarna 330i User Manual

40 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

330i, 535i XP

EN Operator's manual 2-36

Table of Contents

Other manuals for Husqvarna 330i

Workshop Manual32 pages

Questions and Answers:

H
Hailey MartinSep 5, 2025
What to do if there is no indication light on the keypad of Husqvarna Chainsaw?
- S
  Shannon DavisSep 5, 2025
  If your Husqvarna Chainsaw works but there is no indication light on the keypad, it could be due to a defective connection in the keypad connector. Perform a check of the keypad function using a battery diagnostic tool and ensure the keypad connector is correctly assembled, dry, undamaged, and free of corrosion. Alternatively, the keypad might be broken and need replacement.
S
Stephanie DanielsAug 23, 2025
What to do if the red error LED flashes on my Husqvarna 330i?
- K
  Karen ClarkAug 23, 2025
  If the red error LED flashes on your Husqvarna Chainsaw, it could indicate a few issues: * The battery might be empty, in which case you should charge the battery. * There could be a temperature deviation. Use the battery in temperatures between -10°C (14°F) and 40°C (104°F). * There might be an overvoltage issue. Remove the battery from the battery charger.
C
Collin SanchezSep 3, 2025
What does it mean if a warning sign flashes continuously on Husqvarna 330i Chainsaw keypad?
- K
  Kenneth RodriguezSep 3, 2025
  If a warning sign on the keypad of your Husqvarna Chainsaw flashes continuously, it could be due to several reasons: the temperature might be too high (wait for the product to cool down for a maximum of 5 minutes), the temperature of the control unit or battery might be too low (ensure the product and battery are not colder than -10° C), or the front handle safety switch might be stuck in the engaged position (disassemble the front handle and remove any dirt).
T
Tammy SandersSep 2, 2025
What does it mean if a warning sign shows a red light on Husqvarna Chainsaw keypad?
- S
  Shannon WatersSep 2, 2025
  If a warning sign shows a red light on the keypad of your Husqvarna Chainsaw, it indicates that permanent error codes are preventing the product from running. Erase the error codes using a diagnostic tool. Alternatively, the control unit might be broken and need replacement.
C
Courtney WellsAug 31, 2025
Why Husqvarna 330i Chainsaw product stops when I apply work load?
- S
  Stephanie ShieldsSep 1, 2025
  If your Husqvarna Chainsaw stops when you apply a workload, it may be due to a defective connection in the keypad connector. Ensure that the power connectors between the battery and the product are clean and not damaged.
L
linda27Aug 30, 2025
What to do if Husqvarna Chainsaw motor makes sudden movement, then stops?
- P
  Patrick ManningAug 31, 2025
  If the electrical motor of your Husqvarna Chainsaw makes a sudden movement when you push the power trigger and then stops, it is likely due to a short circuit in the control unit. Replace the control unit.
R
Richard BoyleAug 29, 2025
What to do if Husqvarna Chainsaw shows red light after installing a new control unit?
- M
  Misty BergerAug 29, 2025
  If your Husqvarna Chainsaw shows a red light after installing a new control unit, it may be because the spare part comes without software. Use a diagnostic tool to install the software.
M
Mitchell JohnsonAug 28, 2025
What to do if Husqvarna 330i charger does not start?
- A
  Alec GrahamAug 28, 2025
  If the Husqvarna Chainsaw charger doesn't start and no LEDs light up when the battery is attached, check the following: ensure the connection between the charger and battery is clean and undamaged. Also, check the battery. If the issue persists, the charger itself may be defective. Disconnect the charger from the mains outlet for at least 1 minute, then reconnect it. Verify that the fan starts and a green LED illuminates for about 3 seconds. If not, replace the charger.
M
Mitchell BoydAug 27, 2025
What to do if a warning sign flashes red on the battery of Husqvarna 330i Chainsaw?
- M
  Michelle WellsAug 27, 2025
  If a warning sign flashes red on the Husqvarna Chainsaw battery when you press the start button, it could be due to several reasons: the battery temperature might be too high (wait until it cools down, or insert it into the charger to cool it faster), the voltage might be too low (charge the battery), the temperature could be too low (ensure the battery temperature is above -10° C), or the battery itself might be defective (replace it).
A
Angela RodriguezAug 27, 2025
Why Husqvarna 330i won't start and no LEDs are on?
- A
  Angel JonesAug 27, 2025
  If your Husqvarna Chainsaw doesn't start and no LEDs light up when you press the power button, there could be several reasons. First, the battery might be defective; press the on/off button to check the battery – at least one green LED should illuminate. Other potential causes include a defective connection between the battery and the product (ensure the connectors are clean and undamaged), a faulty connection in the keypad connector (make sure it's correctly assembled, dry, undamaged, and free from corrosion), a broken keypad (replace it), damaged cables between the control unit and keypad/main switch (repair or replace them if damaged), or a short circuit in the control unit (replace it).

Husqvarna 330i Specifications

General

Brand	Husqvarna
Model	330i
Category	Chainsaw
Language	English

Related product manuals

Preview: Husqvarna 33

Preview: Husqvarna 336

Preview: Husqvarna 334T

Preview: Husqvarna 339XP

Husqvarna 339XP

Preview: Husqvarna 335XPT

Husqvarna 335XPT

Husqvarna 339 XP

Husqvarna 336 339XP

Husqvarna 338XPT EPA III

Preview: Husqvarna 335XPT California

Husqvarna 335XPT California

Preview: Husqvarna 365

Preview: Husqvarna 340