Why Husqvarna Lawn Mower has no drive?
If your Husqvarna Lawn Mower has no drive, it could be because the product has gotten caught on something and has been slipping; free the product and address the cause. If wet grass is the issue, wait for the lawn to dry before using the mower. A steep slope in the work area can also cause this; steep slopes should be isolated. Ensure the guide wire is laid diagonally across any slopes.
What to do if my Husqvarna Automower 405X Lawn Mower has a battery problem?
If your Husqvarna Lawn Mower is showing a battery problem, it could be due to a temporary battery or firmware-related issue; try restarting the product. It could also be due to an incorrect type of battery, so use original batteries recommended by the manufacturer.
Why is my Husqvarna Lawn Mower going outside working area?
If your Husqvarna Lawn Mower is operating outside the designated working area, several factors could be the cause. First, check that the boundary wire is correctly connected to the charging station. Ensure the boundary wire isn't too close to the work area's edge and that it's properly laid out, especially if the work area has slopes near the boundary wire. If there's an island, verify the boundary wire isn't crossed on its way to or from it. If the product is struggling to distinguish the signal due to nearby installations, place it in the charging station and generate a new loop signal. Finally, disturbances from magnetic objects or buried cables can interfere; try moving the boundary wire or creating additional islands in the work area.
What to do if my Husqvarna Automower 405X says low battery?
If your Husqvarna Lawn Mower is displaying a 'Low battery' message, there are several potential reasons. The product may be unable to locate the charging station, in which case, you should consider changing the position of the guide wire. It's also important to check the installation settings related to finding the charging station. The battery itself might be spent, so performing a battery test is advisable. Lastly, a defective charging station antenna could be the issue; check if the indicator lamp is flashing red, and if necessary, replace the baseplate of the charging station.
How to fix Husqvarna Lawn Mower guide not found?
If your Husqvarna Lawn Mower is displaying 'Guide not found', it could be due to several reasons. Check that the guide wire connector is tightly connected to the charging station. A break in the guide wire could also be the problem; find the break and replace the damaged section using a new loop wire and an original coupler. Finally, ensure that the guide wire is correctly connected to the boundary loop.
What to do if my Husqvarna Automower 405X is stuck in charging station?
If your Husqvarna Lawn Mower is stuck in the charging station, it could be due to an obstruction preventing it from leaving. Remove any objects that might be in its path. Alternatively, the product might be sliding on the baseplate, so try cleaning the baseplate to improve traction.
Why is my Husqvarna Automower 405X Lawn Mower charging station blocked?
If your Husqvarna Lawn Mower is displaying 'Charging station blocked', it could be due to an object obstructing the product from entering. Remove any objects that are in the way. Another possible cause is a bent baseplate; ensure that the baseplate is placed on level ground. Lastly, poor contact between the charging plates and contact plates can prevent charging; put the product in the charging station and check that these plates make good contact.
How to fix cutting system blocked on Husqvarna Automower 405X Lawn Mower?
If the cutting system of your Husqvarna Lawn Mower is blocked, it could be due to grass or other objects wrapped around the drive wheel. Clean the wheels and the area around them. Another cause could be the blade disc lying in a pool of water, so move the product and prevent water from collecting in the work area. Also, if the grass is too high, cut it before using the mower, ensuring it's no more than 10 cm / 3.9 in.
What causes Husqvarna Lawn Mower wheel motor overloaded error?
If your Husqvarna Lawn Mower displays 'Wheel motor overloaded, right/left', it is likely that grass or another object has wrapped around the drive wheel. You should check the drive wheel and remove any obstructions.
How to troubleshoot Husqvarna Lawn Mower front loop sensor problem?
If your Husqvarna Lawn Mower is displaying 'Loop sensor problem, front', the cabling to the sensor circuit board may be faulty or loose. Check the cabling and refit or replace it if necessary. Alternatively, the front loop sensor circuit board itself may be faulty, requiring a check and replacement if needed. An electronic or software-related problem could also be the cause, so check the levels for the A signal.
General| Product Name | Husqvarna Automower 405X |
|---|---|
| Category | Lawn Mower |
| Cutting Width | 22 cm |
| Cutting Height, min-max | 20-50 mm |
| Battery Type | Li-Ion |
| Typical Charging Time | 60 min |
| Sound Level | 62 dB(A) |
| Working Area Capacity | 600 m² |
| Maximum Slope Performance Inside Installation | 40% |
| Maximum Slope Performance at Boundary | 15% |
| GPS-assisted Navigation | Yes |
| Automower Connect | Yes |
| Battery Voltage | 18 V |
| Connectivity | Bluetooth, Cellular |
| Weather Resistance | Yes |
| Smartphone App | Yes |
| Blade Type | Pivoting razor blades |
Illustrates and lists all components of the Husqvarna Automower product.
Explains the meaning of WARNING, CAUTION, and NOTE in the manual.
Provides essential safety instructions for operating the Automower.
Covers safety guidelines specific to installing the charging station and power supply.
Details safety measures to follow during the operation of the Automower.
Outlines safety instructions to be followed before performing maintenance.
Highlights critical safety information regarding the handling of lithium-ion batteries.
Details where to place the boundary wire, considering obstacles and slopes.
Detailed steps for installing the charging station, including safety precautions.
Step-by-step guide for installing the boundary wire and connecting it.
Instructions for installing the guide wire and connecting it.
Steps for setting up basic functions like language, country, and PIN.
Introduces the app's features for controlling and monitoring the Automower.
Instructions to pair the Automower Connect app with the product via Bluetooth.
Details the AIM technology for creating virtual lawn maps and zones.
Information about setting up the product's mowing schedule.
Step-by-step guide to set the daily or weekly mowing schedule.
How to set and adjust the cutting height for optimal grass cutting.
Guide to selecting and setting the desired security level for the product.
Instructions for changing the product's PIN code for security.
Steps to enable and configure the weather timer function.
Details GPS assisted navigation and specialized mowing modes.
Guide to enabling GPS assisted navigation for optimal operation.
How to set up lawn coverage for specific work areas and zones.
How to activate the virtual fence feature for theft protection.
Step-by-step instructions for starting the product and selecting operating modes.
Instructions on how to charge the product's battery correctly.
Detailed steps for cleaning the chassis and blade disc.
Importance of using genuine blades and safety precautions for replacement.
Step-by-step guide on how to replace the product's blades.
Information on battery charging, lifespan, and replacement.
Guide to resolving product faults and symptoms.
Lists product fault messages, their causes, and recommended actions.
Lists common product symptoms and their potential causes.
Lists information and warning messages, their causes, and actions.
Explains the meaning of the charging station's indicator lamp colors and patterns.
Provides a table of symptoms and their causes for troubleshooting.
Guide on how to locate breaks in the boundary or guide loop wire.
Detailed technical data for the 405X and 415X models.
Details the warranty coverage, duration, and conditions for the product.
To Next Page
