How to fix a cutting height that is blocked on a Husqvarna Lawn Mower?
If the cutting height adjustment on your Husqvarna Lawn Mower is blocked, it's probably because grass or other debris has become wrapped around the cutting height adjustment mechanism or lodged between the blade disc and the chassis. Examine the blade disc and the bellows around the cutting height adjustment, and clear away any stuck grass or objects.
What to do if the cutting system is blocked on my Husqvarna AUTOMOWER 450XH Lawn Mower?
If the cutting system on your Husqvarna Lawn Mower is blocked, it could be due to grass or other objects wound around the blade disc. Inspect the blade disc and remove any obstructions. Alternatively, the blade disc might be sitting in a pool of water. In this case, relocate the mower and take steps to prevent water from accumulating in the mowing area.
What to do if the Husqvarna AUTOMOWER 450XH has a blue flashing light?
If your Husqvarna Lawn Mower displays a blue flashing light, it could be due to a disconnected boundary loop or a break in the boundary loop. First, ensure the boundary wire connectors are properly fitted to the charging station. If the issue persists, there may be a break in the boundary loop. Locate the break, replace the damaged section with a new loop wire, and splice it using an original coupler.
Why is the Husqvarna AUTOMOWER 450XH charging station showing a solid red light?
A solid red light on the Husqvarna Lawn Mower charging station indicates a fault in the circuit board or an incorrect power supply. Unfortunately, this issue requires professional attention.
What to do if the Husqvarna AUTOMOWER 450XH has a red flashing light?
A red flashing light on your Husqvarna Lawn Mower indicates an interruption in the charging station’s antenna. Unfortunately, this issue requires professional attention.
Why is the wheel motor blocked on my Husqvarna AUTOMOWER 450XH Lawn Mower?
If the wheel motor of your Husqvarna Lawn Mower is blocked, it's likely due to grass or other objects tangled around the drive wheel. Check the drive wheel and carefully remove any obstructions you find.
What to do if my Husqvarna AUTOMOWER 450XH Lawn Mower is trapped?
If your Husqvarna Lawn Mower gets trapped, it may be stuck in a confined area with multiple obstacles. Check the area for obstructions that could be hindering the mower's movement.
General| Cutting Width | 24 cm |
|---|---|
| Maximum Lawn Area | 5000 m² |
| Battery Type | Li-Ion |
| Battery Voltage | 18 V |
| Cutting Height | 20-60 mm |
| Maximum Incline Within The Working Area | 45% |
| Active Time | 24 h |
| Cutting System | 3 pivoting razor blades |
| Navigation | GPS-assisted navigation |
| Overall dimensions (LxWxH) | 72 x 56 x 31 cm |
| Sound level Measured | 58 dB(A) |
| Weather Resistance | IPX5 |
| Installation Required | Yes |
| Connectivity | Bluetooth |
| Feature | Lift & Tilt Sensor |
| Working Time | Up to 270 minutes |
Information on product support and its features.
Visual guide to product components and safety symbols.
Explains menu structures, display, and keypad functions.
Crucial safety instructions, warnings, and definitions.
Specific safety guidelines for operating the product safely.
Introduction, components, and general preparations for installation.
Planning for boundary and guide wire placement.
Setting up slopes, passages, islands, and secondary areas.
Installing the product, charging station, and required tools.
Detailed steps for installing boundary and guide wires.
Positioning wires with stakes, burying, and extending them.
Visual checks, basic settings, and app setup.
Accessing menus and configuring general product settings.
Setting mowing schedules and security levels.
Changing PIN, creating loop signals, and managing alarm duration.
Adjusting weather timer and managing lawn coverage areas.
Using GPS for optimal operation and setting navigation.
Setting up, testing, and measuring for lawn coverage.
Methods for finding the charging station and testing guide wire.
Testing boundary wire, signal range, and setting corridor/exit angles.
Drive past wire, general settings, and profile management.
Setting ECO mode, spiral cutting intensity, and slope control.
Configuring general product settings like time, date, and language.
Accessory information and Automower Connect pairing.
Setting GeoFence sensitivity, enabling SMS notifications.
Settings for ultrasonic, headlights, and collision avoidance.
Using the main switch and selecting operating modes upon start.
Details on Main, Secondary, Override, Spot Cutting, and Park modes.
How to stop, switch off, and charge the product.
Overview and tasks for chassis, blades, wheels, body, and station.
Procedures for replacing blades and battery information.
Recommendations for servicing before winter storage.
Guide to troubleshooting and common fault messages.
Solutions for loop signal, PIN code, work area, and drive problems.
Addressing alarms, electronic, sensor, and navigation issues.
Understanding info messages and charging station indicator lights.
Diagnosing and resolving product symptoms like docking, vibration, and mowing.
Method for locating breaks in the loop wire.
Guidelines for transporting, storing, and disposing of the product.
Step-by-step instructions for removing the battery.
Detailed specifications including dimensions, electrical, and noise data.
Outlines the terms and conditions of the product warranty.
Product conformity and compliance requirements for US/CA markets.
To Next Page
