Why does my Husqvarna SVARTPILEN 401 have high oil consumption?
If your Husqvarna Motorcycle has high oil consumption, the engine vent hose might be bent, so route the vent hose without bends or change it if necessary. Another possible cause is that the engine oil level is too high, so check the engine oil level. Also the engine oil could be too thin (low viscosity), so change the engine oil and the oil filter, and clean the oil screens.
Why won't my Husqvarna SVARTPILEN 401 engine turn over when I press the start button?
If the Husqvarna Motorcycle engine doesn't turn when you press the start button, it could be due to a few reasons. You might not be following the correct start procedure, so double-check that first. The 12-V battery could be discharged, meaning you'll need to charge it. Also, check the main fuse and fuses 3, 4, and 7, as they might be blown and need replacement. Finally, ensure there's a proper ground connection.
What to do if my Husqvarna SVARTPILEN 401 Motorcycle engine dies during a trip?
If your Husqvarna Motorcycle engine dies while you're riding, the possible cause is lack of fuel, so refuel. Another possible cause is that the main fuse or fuses 3, 4, or 7 are blown, so change the main fuse and the fuses of individual power consumers.
Why does my Husqvarna Motorcycle engine have so little power?
If your Husqvarna Motorcycle engine has too little power, the air filter might be very dirty, so change it. Another possible cause is that the fuel filter is very dirty, in this case check the fuel pressure. It can also be a malfunction in the electronic fuel injection, so read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
Why is my Husqvarna SVARTPILEN 401 Motorcycle engine overheating?
If your Husqvarna Motorcycle engine overheats, there might be too little coolant in the cooling system. Check the cooling system for leakage and check the coolant level. Another possible cause is that the radiator fins are very dirty, so clean the radiator fins.
What does it mean when the ABS warning lamp lights up on my Husqvarna SVARTPILEN 401?
If the ABS warning lamp lights up on your Husqvarna Motorcycle, the ABS fuse might be blown, so change the ABS fuses. It could also be due to a large difference in wheel speeds of the front and rear wheels, in this case stop the vehicle, switch off the ignition, and start it again. Another cause can be a malfunction in ABS, so read out the ABS fault memory using the Husqvarna Motorcycles diagnostics tool.
What causes my Husqvarna Motorcycle to overheat?
If your Husqvarna Motorcycle engine overheats, it could be due to foam formation in the cooling system, so drain the coolant and fill/bleed the cooling system. Another possible cause is a defective thermostat, so check the thermostat. Fuse 5 might be blown, so change the fuses of individual power consumers. Also, there could be a defect in radiator fan system, so check the radiator fan system.
What to do if Husqvarna SVARTPILEN 401 Motorcycle engine turns but does not start?
If the Husqvarna Motorcycle engine turns but does not start, it could be due to an operating error, so carry out the start procedure. Another possible cause is a malfunction in the electronic fuel injection, so read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
What does it mean when the malfunction indicator lamp lights up yellow on my Husqvarna SVARTPILEN 401?
If the malfunction indicator lamp lights up yellow on your Husqvarna Motorcycle, it indicates a possible malfunction in the electronic fuel injection. To address this, read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
Why is the 12 V battery on my Husqvarna SVARTPILEN 401 Motorcycle discharged?
If the 12 V battery of your Husqvarna Motorcycle is discharged, it might be because the ignition was not switched off when the vehicle was parked, so charge the 12-V battery. Another possible cause is that the 12-V battery is not being charged by the alternator, so check the charging voltage and the open-circuit current.
General| Displacement | 373.2 cc |
|---|---|
| Torque | 37 Nm @ 7, 000 rpm |
| Transmission | 6-speed |
| Cooling | Liquid cooled |
| Fuel Tank Capacity | 9.5 liters |
| Seat Height | 835 mm |
| Fuel System | Electronic Fuel Injection |
| Front Suspension | WP APEX 43 |
| Rear Suspension | WP APEX Monoshock |
| Bore x Stroke | 89 mm x 60 mm |
| Compression Ratio | 12.6:1 |
| Starter | Electric |
| Final Drive | Chain |
| Ground Clearance | 145 mm |
| Engine Type | Single cylinder, 4-stroke |
| Power | 32 kW |
| Front Brake | 320 mm disc |
| Rear Brake | 230 mm disc, single-piston caliper |
| ABS | Bosch 9.1MB |
| Wheelbase | 1357 mm |
Explains the meaning of various symbols used in the manual.
Explains the typographical formats used in the document.
Defines intended use and describes dangers of misuse.
Explains hazard symbols (Danger, Warning, Caution, Note) and their meanings.
Covers safety precautions for riding, including dangers of accidents and poisoning.
Stresses the importance of wearing appropriate protective clothing for riding.
Conditions for warranty validity and coverage.
Guidelines for using fuel and auxiliary substances, including environmental hazards.
Importance of regular service, care, and tuning for vehicle longevity.
Illustrates the front-left view of the motorcycle with numbered parts.
Illustrates the rear-right view of the motorcycle with numbered parts.
Explains where to find the Vehicle Identification Number (VIN).
Explains the location of the USA and Canada type labels.
Details how to find and use the key number for ordering spare keys.
Indicates the location of the engine number.
Describes clutch lever, hand brake lever, throttle grip, and handlebar switches.
Describes the ignition and steering lock functions and states.
Details the procedure for opening and closing the fuel tank filler cap.
Explains the location and function of the side stand, including safety system coupling.
Describes how the instrument activates and performs its self-test.
Describes the various areas and information shown on the instrument display.
Details how to change ABS modes (Road, Supermoto) and their functions.
Explains how to set the RPM for the shift warning lights.
General advice and warnings before riding the motorcycle for the first time.
Guidelines for the engine's break-in period, including speed limits.
Warnings and guidelines regarding vehicle weight limits and luggage.
Pre-ride checks covering fluids, brakes, tires, and controls.
Steps and safety precautions for starting the engine and moving off.
Detailed instructions and warnings on how to apply the brakes effectively.
Instructions and safety precautions for stopping and parking the motorcycle.
Instructions and safety warnings related to refueling the motorcycle.
Lists mandatory maintenance tasks at specified intervals.
Lists recommended maintenance tasks at specified intervals.
Explains how to adjust the fork's compression and rebound damping.
Explains how to adjust the shock absorber's rebound damping and spring preload.
Describes handlebar mounting options for rider comfort and adjustment.
Instructions for lifting and removing the motorcycle from lifting gear.
Steps for removing and installing passenger seat and bag carrier.
Detailed steps for removing and installing the left and right side covers.
How to check and clean the drive chain and adjust its tension.
Instructions for installing the license plate bracket.
Explains the function and components of the ABS system.
How to check front and rear brake fluid levels and associated warnings.
How to check the thickness and condition of front and rear brake linings.
How to check and adjust the free travel of the rear brake lever.
Step-by-step guides for removing and installing the front wheel.
Step-by-step guides for removing and installing the rear wheel.
How to check tires for damage, tread depth, age, and pressure.
Instructions for removing, installing, and charging the 12-V battery.
Steps for changing the main fuse and ABS fuses.
How to check and adjust the motorcycle's headlight setting and range.
How to check coolant level and antifreeze protection.
Instructions for draining, filling, and bleeding the cooling system.
Steps for changing the coolant, including safety warnings.
How to check and adjust the free play in the clutch lever.
How to check and adjust the basic position of the shift lever.
How to correctly check the engine oil level.
Step-by-step guide for changing engine oil, filter, and cleaning screens.
Instructions for adding engine oil, including recommended type and quantity.
Guidelines and warnings for cleaning the motorcycle safely and effectively.
Recommendations for preparing the motorcycle for winter storage.
Steps to follow for storing the motorcycle for extended periods.
Steps to take before riding the motorcycle after it has been stored.
Lists common engine and electrical faults, causes, and actions.
Troubleshooting steps for performance issues and warning lamp indicators.
Specifications related to the motorcycle's engine.
Specifications related to the motorcycle's chassis, suspension, and brakes.
Torque values for chassis and engine fasteners.
Standard classification and guidelines for brake fluid and coolant.
Standard classification and recommended suppliers for engine oil.
Standard classification and guidelines for fork and shock absorber fluids.
Fuel specifications and warnings about ethanol/methanol content.
Recommended suppliers and products for chain cleaning and fuel stabilization.
Recommended suppliers and products for motorcycle cleaning and lubrication.
Explanations of JASO T903 MA2 and SAE standards for oils.
Explanation of yellow/orange (error) and green/blue (information) symbols.
To Next Page