What to do if my Husqvarna Vitpilen 401 2018 Motorcycle has high oil consumption?
If your Husqvarna Motorcycle has high oil consumption, it could be due to the engine oil level being too high, so check the engine oil level. Another possible reason is that the engine oil is too thin (low viscosity), so change the engine oil and oil filter and clean the oil screens.
What to do if my Husqvarna Vitpilen 401 2018 engine dies during the trip?
If the engine of your Husqvarna Motorcycle dies during a trip, it might be due to a lack of fuel. In this case, refuel your motorcycle. Another possible reason is that fuse 1, 3, 4, or 7 might be blown. If that is the case, change the fuses of individual power consumers.
Why does my Husqvarna Motorcycle engine not crank when pressing the electric starter button?
If your Husqvarna Motorcycle engine does not crank when you press the electric starter button, it could be due to several reasons. You might be making an operating error, so ensure you carry out the start procedure correctly. The battery might be discharged, so try recharging it. Also, check if fuse 1, 3, 4, or 7 is blown and replace them if needed. Finally, verify that there is a proper ground connection.
What does it mean if the ABS warning lamp lights up on my Husqvarna Vitpilen 401 2018 Motorcycle?
If the ABS warning lamp lights up on your Husqvarna Motorcycle, it could be due to a blown ABS fuse, so replace the ABS fuses. It could also be due to a large difference in wheel speeds between the front and rear wheels; in this case, stop the vehicle, switch off the ignition, and start it again. Another possibility is a malfunction in the ABS, in which case you should read out the ABS fault memory using the Husqvarna Motorcycles diagnostics tool.
Why does my Husqvarna Vitpilen 401 2018 engine overheat?
If your Husqvarna Motorcycle engine overheats, it could be caused by too little coolant in the cooling system. Check the cooling system for leaks and verify the coolant level. Another cause could be very dirty radiator fins, so clean the radiator fins.
How to fix a Husqvarna Motorcycle engine with too little power?
If your Husqvarna Motorcycle engine has too little power, the air filter might be very dirty, so change the air filter. Alternatively, the fuel filter might be very dirty, so check the fuel pressure. It could also be a fault in the fuel injection system, so read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
What does it mean if the malfunction indicator lamp lights up yellow on my Husqvarna Vitpilen 401 2018 Motorcycle?
If the malfunction indicator lamp lights up yellow on your Husqvarna Motorcycle, it indicates a fault in the fuel injection system. The suggested solution is to read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
What to do if Husqvarna Motorcycle engine turns but does not start?
If your Husqvarna Motorcycle engine turns but does not start, it could be due to an operating error, so ensure you carry out the start procedure correctly. Alternatively, there may be a fault in the fuel injection system, so read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
Why is my Husqvarna Vitpilen 401 2018 Motorcycle battery discharged?
If the battery of your Husqvarna Motorcycle is discharged, it might be because the ignition was not switched off when the vehicle was parked, so recharge the battery. Another possibility is that the battery is not being charged by the alternator, so check the charging voltage and the open-circuit current.
Why does my Husqvarna Motorcycle engine turn only if the clutch lever is drawn?
If the engine of your Husqvarna Motorcycle only turns when the clutch lever is drawn, it's likely because the vehicle is in gear. Shift gear to neutral. It could also be that the vehicle is in gear and the side stand is folded out, so shift gear to neutral.
Defines the intended use of the vehicle and highlights dangers associated with misuse.
General safety instructions and definitions of risk levels (Danger, Warning, Caution) with symbols.
Identifies and locates various warning and information labels on the motorcycle.
Critical guidelines for safe vehicle operation, including rider fitness and environmental factors.
Describes the location and function of the clutch and hand brake levers on the handlebar.
Details the throttle grip and the function of switches on the left side of the handlebar.
Details switches on the right handlebar, including ignition and steering lock functions.
Details the location and function of the shift lever, foot brake lever, and side stand.
Overview of the instrument cluster, its components, and activation sequence upon ignition.
Explains warning notes, indicator lamp functions, and how they signal vehicle status or issues.
Critical safety checks for first use and guidelines for the engine's running-in phase.
Safety warnings and recommendations regarding vehicle weight limits and proper luggage handling.
Checklist for pre-ride inspections and step-by-step instructions for starting the engine.
Guidance on smooth gear engagement for starting off and proper shifting techniques.
Instructions on effective brake application, ABS function, and safety warnings.
Procedures for safely stopping, parking the vehicle, and guidelines for transportation.
Instructions for refueling the motorcycle, including safety precautions and fuel type.
Instructions on adjusting the rear shock absorber's spring preload for different load conditions.
Explanation of the ABS system, its components, and warnings about modifications.
Procedure for checking the thickness and condition of the front and rear brake discs.
Instructions for verifying front and rear brake fluid levels and identifying potential issues.
Detailed steps for adding front and rear brake fluid, including safety precautions.
Method for checking the minimum thickness and condition of front and rear brake linings.
Step-by-step instructions for safely removing and reinstalling the front wheel.
Step-by-step instructions for safely removing and reinstalling the rear wheel.
Procedures for checking coolant level and antifreeze concentration with safety warnings.
Detailed steps for checking coolant levels in the compensating tank and radiator.
Procedure for checking engine oil level, considering engine temperature and waiting times.
Detailed steps for oil change, filter replacement, and oil screen cleaning.
General| Bore x Stroke | 89 mm x 60 mm |
|---|---|
| Compression Ratio | 12.6:1 |
| Fuel System | Electronic fuel injection |
| Starter | Electric |
| Transmission | 6-speed |
| Final Drive | Chain |
| Frame | Steel trellis frame |
| Rear Brake | 230 mm disc, single-piston caliper |
| Engine | 373.2cc liquid cooled single cylinder, four stroke engine |
| Power | 44 hp |
| Torque | 37 Nm @ 7, 000 rpm |
| Front Suspension | USD fork, 43 mm |
| Rear Suspension | Monoshock |
| Front Brake | 320 mm disc |
| Front Tire | 110/70-17 |
| Rear Tire | 150/60-17 |
| Seat Height | 830 mm |
| Fuel Capacity | 9.5 L |
To Next Page