from 3 to 5 years may be provided by engine or pump
manufacturer.
GENERAL CONDITIONS: Hydro Tek’s responsibility
with respect to claims is limited to making the required
repairs or replacements to the original retail purchaser,
and no claim of breach of warranty shall be cause for
any cancellation or rescission of the contract of sale of
any Hydro Tek product. Hydro Tek reserves the right
to change or improve the design of any of its products
or illustrations without assuming any obligation to
modify any product previously manufactured.
This supersedes any and all previous warranty
statements for products purchased after November
2015. Hydro Tek is not liable for indirect, incidental or
consequential damages including any cost of substitute
equipment, loss of revenue, pecuniary expense or loss,
or inability to use a Hydro Tek product. Hydro Tek
disclaims all implied warranties, including those of
merchantability and fitness for use for a particular
purpose. Some states do not allow exclusions or
limitations on how long an implied warranty lasts, so the
above exclusions may not apply to you. It is the buyer’s
responsibility to ensure installation and use of Hydro
Tek products conforms to local codes.
INTERNATIONAL END USERS: Warranty is furnished
by authorized Hydro Tek dealers or distributors only;
and the warranty may vary depending on the dealer or
distributor and may be different from Hydro Tek’s
warranty; please consult distributor for details.
HOW TO OBTAIN WARRANTY SERVICE:
1. List washer model#______________________.
List serial #____________________ (on base plate of
machine near the motor/engine).
2. Contact your local service dealer and return the
Hydro Tek washer or part within the warranty period
along with your sales receipt. To locate service, call
customer service at Hydro Tek or go to:
www.hydrotek.us and enter your zip code.
3. You also have the option to obtain a return goods
authorization and ship the questionable part freight
prepaid directly to the manufacturer. The part will be
evaluated upon receipt. If found defective, Hydro Tek
will repair or replace part under the conditions of
warranty and return to you.
4. If the defective component is an engine or motor
made by another manufacturer, we, or your authorized
Hydro Tek dealer, can help you obtain warranty service
through the specific manufacturer’s local authorized
service center.
5. If you are unable to resolve the warranty claim, write
to Hydro Tek Systems, Inc. 2353 Almond Ave.
Redlands, CA 92374 USA, Attn.: Technical Services.
Please enclose a copy of the dated purchase receipt
and explain the nature of the defect.
EVAPORATIVE EMISSION CONTROL STATEMENT
The California Air Resources Board and Hydro Tek
Systems, Inc. are pleased to explain the evaporative
emission control system’s warranty on your 2023
Pressure Washer. In California, new equipment that
use small off-road engines must be designed, built, and
equipped to meet the State’s stringent antismog
standards. Hydro Tek Systems, Inc. must warrant the
evaporative emission control system on your Pressure
Washer for the period listed below provided there has
been no abuse, neglect or improper maintenance of
your equipment leading to the failure of the evaporative
emission control system.
Your evaporative emission control system may include
parts such as: carburetors, fuel tanks, fuel lines (for
liquid fuel and fuel vapors), fuel caps, valves, canisters,
filters, clamps, connectors, and other associated
components.
MANUFACTURER’S WARRANTY COVERAGE:
This evaporative emission control system is warranted
for two years. If any evaporative emission-related part
on your equipment is defective, the part will be repaired
or replaced by Hydro Tek Systems, Inc.
OWNER’S WARRANTY RESPONSIBILITIES:
As the Pressure Washer owner, you are responsible for
performance of the required maintenance listed in your
owner’s manual. Hydro Tek Systems, Inc. recommends
that you retain all receipts covering maintenance on
your Pressure Washer, but Hydro Tek Systems, Inc.
cannot deny warranty coverage solely for the lack of
receipts.
As the Pressure Washer owner, you should be aware
that Hydro Tek Systems, Inc. may deny you warranty
coverage if your Pressure Washer or a part has failed
due to abuse, neglect, or improper maintenance or
unapproved modifications.
You are responsible for presenting your Pressure
Washer to a Hydro Tek Systems, Inc. distribution center
or service center as soon as the problem exists. The
warranty repairs shall be completed in a reasonable
amount of time, not to exceed 30 days. If you have a
question regarding your warranty coverage, you should
contact Hydro Tek Systems, Inc., at 1-909-799-9222.
GENERAL EMISSIONS WARRANTY COVERAGE:
Designed, built, and equipped so as to conform with all
applicable regulations; and free from defects in
materials and workmanship that causes the failure of a
warranted part for a period of two years.
The warranty on evaporative emissions-related parts
will be interpreted as follows:
(1) Any warranted part that is not scheduled for
replacement as required maintenance in the written
instructions required by 13 CCR § 2760 (e) must be
warranted for the warranty period defined above. If any
such part fails during the period of warranty coverage,
WARRANTY-EMISSION CONTROL 3
To Next Page
Loading...
Need help?
General
