Hydro Tek CPS Series User Manual

it must be repaired or replaced by the Holder or the
Holder’s contracted warranty provider according to
subsection (4) below. Any such part repaired or
replaced under the warranty must be warranted for a
time not less than the remaining warranty period.
(2) Any warranted part that is scheduled only for regular
inspection in the written instructions required by 13
CCR § 2760 (e) must be warranted for the warranty
period defined above. A statement in such written
instructions to the effect of “repair or replace as
necessary” shall advise owners of the warranty
coverage for evaporative emissions related parts.
Replacement within the warranty period is covered by
the warranty and will not reduce the period of warranty
coverage. Any such part repaired or replaced under
warranty must be warranted for a time not less than the
remaining warranty period.
(3) Any warranted part that is scheduled for
replacement as required maintenance in the written
instructions required by 13 CCR § 2760 (e) must be
warranted for the period of time prior to the first
scheduled replacement point for that part. If the part
fails prior to the first scheduled replacement, the part
must be repaired or replaced by the manufacturer
according to subsection (4) below. Any such part
repaired or replaced under warranty must be warranted
for a time not less than the remainder of the period prior
to the first scheduled replacement point for the part.
(4) Repair or replacement of any warranted part under
the warranty provisions of this article must be
performed at no charge to the owner at a warranty
station.
(5) Notwithstanding the provisions of subsection (4)
above, warranty services or repairs must be provided at
distribution centers that are franchised to service the
subject engines or equipment.
(6) The owner must not be charged for diagnostic labor
that leads to the determination that a warranted part is
in fact defective, provided that such diagnostic work is
performed at a warranty station.
(7) Throughout the evaporative emission control
system's warranty period set out in subsection (b)(2),
the Holder or the Holder’s contracted warranty provider
must maintain a supply of warranted parts sufficient to
meet the expected demand for such parts and must
obtain additional parts if that supply is exhausted.
(8) Manufacturer-approved replacement parts that do
not increase the exhaust or evaporative emissions of
the engine or evaporative emission control system must
be used in the performance of any warranty
maintenance or repairs and must be provided without
charge to the owner. Such use will not reduce the
warranty obligations of the Holder or the Holder’s
contracted warranty provider.
(9) The use of add-on or modified parts may be grounds
for disallowing a warranty claim made in accordance
with this Article. The Holder or the Holder’s contracted
warranty provider will not be liable under this Article to
warrant failures of warranted parts caused by the use
of an add-on or modified part.
(10) The Holder shall provide any documents that
describe that Holder warranty procedures or policies
within five working days of request by the Executive
Officer.
WARRANTED PARTS:
The repair or replacement of any warranted part
otherwise eligible for warranty coverage may be
excluded from such warranty coverage if Hydro Tek
Systems, Inc. demonstrates that the Pressure Washer
has been abused, neglected, or improperly maintained,
and that such abuse, neglect, or improper maintenance
was the direct cause of the need for repair or
replacement of the part. That notwithstanding, any
adjustment of a component that has a factory installed,
and properly operating, adjustment-limiting device is
still eligible for warranty coverage. The following
emission warranty parts list are covered (use portions
of this list applicable to your Pressure Washer):
(1) ............................................................... Fuel Tank
(2) ................................................................ Fuel Cap
(3) .............. Fuel Lines (for liquid fuel and fuel vapors)
(4) .................................................... Fuel Line Fittings
(5) ................................................................. Clamps*
(6) .......................................... Pressure Relief Valves*
(7) ...................................................... Control Valves*
(8) .................................................. Control Solenoids*
(9) ................................................ Electronic Controls*
(10) .............................. Vacuum Control Diaphragms*
(11) .................................................... Control Cables*
(12) ................................................. Control Linkages*
(13) ...................................................... Purge Valves*
(14) .............................................................. Gaskets*
(15) ......................................... Liquid/Vapor Separator
(16) ................................................... Carbon Canister
(17) ................................. Canister Mounting Brackets
(18) ......................... Carburetor Purge Port Connector
*Note: As they relate to the evaporative emission
control system.
ELECTRICAL PRECAUTIONS:
1. Observe all State, Local, and National codes for
the installation of your electrically powered washer.
2. For a grounded product rated 250 volts, single
phase, or less: This product is provided with a ground
fault circuit interrupter built into the power cord plug.
(8hp single phase excluded; order GFCI separately). If
replacement of the plug or cord is needed, use only
identical replacement parts.
3. GROUNDING INSTRUCTIONS:
Cord Connected, Grounded Products:
WARRANTY – SAFETY WARNINGS 4

Hydro Tek CPS Series Specifications

General

Brand	Hydro Tek
Model	CPS Series
Category	Pressure Washer
Language	English