Why do my Hydrofarm Controller fixtures fail to turn off?
If Hydrofarm Controller fixtures fail to turn off, it might be due to having too many fixtures, which can cause residual voltage in the cable system. Try reducing the number of fixtures per zone to resolve this issue.
How to fix Hydrofarm Autopilot PX2 screen when it does not work after connecting power supply?
If the Hydrofarm Controller screen isn't working after you've connected the power supply, unplug the DC connector from the controller momentarily. Then, reconnect it, making sure the connector is fully inserted and tightened.
What to do if Hydrofarm Autopilot PX2 Controller does not control fixtures?
If the Hydrofarm Controller isn't controlling the fixtures, try reconnecting the signal cable. Then, check each fixture individually to find where the communication is being lost.
What to do if Hydrofarm Autopilot PX2 Controller does not show temperature after connecting with temperature probe?
If the Hydrofarm Controller isn't showing the temperature after you connect the temperature probe, try disconnecting and then reconnecting the temperature probe.
What to do if fixture status is different from the power set by Hydrofarm Autopilot PX2 Controller?
If the fixture status is different from the power set by the Hydrofarm Controller, adjust the time of sunrise and sunset or reset the temperature limits.
What to do if some Hydrofarm Autopilot PX2 fixtures work normally, while others function abnormally?
If, when connecting several fixtures, the first few work fine but the rest don't function properly with your Hydrofarm Controller, try reconnecting the signal cable. Also, check for and replace any damaged fixtures.
Why won't my Hydrofarm Controller fixtures turn off?
If your Hydrofarm Controller fixtures are not turning off, it may be due to having too many fixtures connected, which can cause residual voltage in the cable system. Try reducing the number of fixtures per zone.
How to fix Hydrofarm Controller screen that does not work after connecting power supply?
If the screen on your Hydrofarm Controller isn't working after connecting the power supply, unplug the DC connector from the controller momentarily, then reconnect it. Make sure the connector is fully inserted and tightened.
What to do if some fixtures work abnormally when connecting several fixtures to the Hydrofarm Autopilot PX2?
If some fixtures function abnormally when connecting several fixtures to the Hydrofarm Controller, try reconnecting the signal cable. If the problem persists, replace any damaged fixture.
How to fix a Hydrofarm Autopilot PX2 screen that doesn't work after connecting the power supply?
If the screen of your Hydrofarm Controller doesn't work after connecting the power supply, unplug the DC connector from the controller momentarily, then reconnect it. Ensure the connector is fully inserted.
Independent zone control, spectral optimization, power saving, and advanced features like dimming.
Two sensors provide data for auto-dimming and high-temperature shutdown.
Shielded cables for reliability, eliminates traditional contactors, reduces infrastructure cost.
Lists all items included in the Autopilot PX2 controller package.
Details voltage, frequency, and control capacity for HID and LED fixtures.
Securely mount the PX2 controller to a wall using provided screws and holes.
Connect the power adapter and attach temperature/signal probes to the bottom panel.
Route probe cables neatly to the ceiling, ideally suspending them.
Shield probes from direct light to prevent inaccurate readings and premature dimming.
Configure zones for controlling up to 50 LED fixtures each.
Configure zones for controlling up to 256 HID fixtures each.
Set Zone A for LEDs and Zone B for HIDs.
Configure units (temp, power), time format, time, and date for the controller.
Cycle through Zone A/B Setup and Output Schedule, and System Setting.
Set Type, Power, R/S, Dim, Stop, and Delay for Zone A.
All settings must be saved for the controller to function properly.
Repeat the setup process for Zone B.
Schedule up to six output levels (wattage/percentage) for the light cycle.
Save the programmed schedule for Zone A and repeat for Zone B.
Refer to pages 8-23 for detailed cable guides on various lighting configurations.
Meaning of controller LEDs (A-G) for status, protection, and signal output.
Solutions for problems like screen errors, fixture control issues, and temperature probe detection.
Connect PHOTOBIO fixtures using the PHOTO-LOC 0-10V cable kit.
Identifies cable ends (Female, Male) and T Connector for LED fixtures.
Connects Phantom HID fixtures using RJ data link and RJ12 T-connectors.
Legend for HID connections: RJ Data Link, RJ12 T-Connector, RJ12 to USB.
Connects Core 2.0 fixtures using IP rated data link and Wieland harness.
Legend for Core 2.0 connections: Data Link, Wieland Harness, Junction Box, Input/Output.
Connects LED and CMH fixtures using the PHOTO-LOC 0-10V cable kit.
Legends for LED (PHOTO-LOC) and HID (RJ12) connections in mixed setups.
Connects LED and HPS fixtures using the PHOTO-LOC 0-10V cable kit.
Legends for LED (PHOTO-LOC) and HID (RJ12) connections in mixed setups.
Connects dual zone HPS fixtures using RJ data link and RJ12 T-connectors.
Legend for HID connections: Data Link, RJ12 T-Conn, RJ12 to USB.
Connects HPS and CMH fixtures using RJ data link and RJ12 T-connectors.
Legend for HID connections: Data Link, RJ12 T-Conn, RJ12 to USB.
Connects HPS and MH fixtures using RJ data link and RJ12 T-connectors.
Legend for HID connections: Data Link, RJ12 T-Conn, RJ12 to USB.
Covers defects for 3 years; excludes misuse, abuse, or failure to follow instructions.
Liability limited to replacement cost; excludes consequential or incidental damages.
Return product to place of purchase with receipt for repair or replacement.
General| Type | Environmental Controller |
|---|---|
| Amperage | 15A |
| Power Consumption | 1800W |
| Number of Outlets | 2 |
| Control Outputs | 2 |
| Display | LCD |
| Timer Function | Yes |
| Temperature Range | 32°F to 122°F (0°C to 50°C) |
| Voltage | 120V |
To Next Page
