HySecurity SlideSmart DC 15 Installation Manual

HySecurity SlideSmart DC 15

8 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Installation Manual

for HyNet Attachment Bracket Kit: MX3866

SwingSmart DC 20 and SwingSmart DCS 20

SlideSmart DC 15 and SlideSmart DCS 15

SlideSmart DC 10F and SlideSmart DCS 10F

This document is a supplemental document that provides specic information regarding

conguration of the HySecurity gate operator with installation and wiring of the HyNet Gateway.

For safety considerations and information specic to your gate operator, refer to the HySecurity

gate operator product manuals.

www.SecureOpeners.com | (800) 878-7829 | Sales@SecureOpeners.com

Other manuals for HySecurity SlideSmart DC 15

Installation And Reference Manual148 pages

Installation And Maintenance Manual144 pages

Questions and Answers:

M
Michelle EdwardsAug 15, 2025
Why is there a communication failure between master and slave in HySecurity Gate Opener?
- C
  Casey AndersenAug 15, 2025
  In a dual gate setup, communication issues between the master and slave units can arise from several factors. Ensure the master/slave communication cable is correctly installed and that each operator is properly configured via the Installer Menu, with one set as Master and the other as Slave. Ground each operator according to NEC/NFPA standards and use a separate conduit for communication cables, avoiding high-voltage AC power. Verify AC power is present at both operators and all power switches are ON. Also, check that both operators are running the same software version, which you can view by pressing RESET.
R
rodriguezrebeccaAug 18, 2025
What to do if there are motor wiring issues in HySecurity SlideSmart DC 15?
- M
  Michael GoodwinAug 18, 2025
  If your HySecurity Gate Opener isn't working due to motor wiring issues, first check the DC motor wires to ensure they are connected. Next, verify that the DC power switch is turned on. Finally, press the RESET button to clear the fault.
T
tim28Aug 22, 2025
What causes internal communication error in HySecurity SlideSmart DC 15 Gate Opener?
- R
  Rebecca BrownAug 22, 2025
  If the Smart DC Controller in your HySecurity Gate Opener detects an internal communications error, it could be due to excessive electrical noise, a lack of earth grounding, or an internal problem with the controller. Try to identify and fix the source of electrical noise. Install a ground rod, and if the issue persists, consider replacing the Smart DC Controller.
A
Allison NortonAug 26, 2025
How to fix target magnet on chain missing in HySecurity Gate Opener?
- S
  sandra96Aug 26, 2025
  If the target magnet on the chain of your HySecurity Gate Opener is missing or not being detected, ensure the target is properly fastened to the chain. Check the target sensor to confirm it's reading the magnet. If the sensor or its wires are damaged, replace the sensor.
I
igarrettAug 28, 2025
What happens if HySecurity Gate Opener motor overheats?
- R
  Rachael BrownAug 29, 2025
  If your HySecurity Gate Opener's motor drive heat sink exceeds a temperature of 210°F, the operator will temporarily disable itself. It will automatically reset once it cools down.
B
Brian ColemanSep 1, 2025
What to do if HySecurity SlideSmart DC 15 Gate Opener has gate hardware issues?
- Y
  ythorntonSep 1, 2025
  If your HySecurity Gate Opener is experiencing issues due to gate hardware, inspect and correct any problems with the gate hardware as needed. This can also be caused by ice or snow buildup.
T
Tara AdamsSep 4, 2025
Why HySecurity SlideSmart DC 15 Gate Opener batteries are drained?
- M
  Margaret TownsendSep 4, 2025
  If your HySecurity Gate Opener's batteries are drained because AC power has been off for too long, check the condition of the batteries.
T
Tara BaxterSep 7, 2025
What to do if HySecurity SlideSmart DC 15 battery voltage is low?
- M
  Mary LongSep 8, 2025
  If your HySecurity Gate Opener's battery voltage has dropped below 22V, check the condition of the battery.
J
Jordan NicholsonSep 12, 2025
How to restore AC power to HySecurity Gate Opener?
- N
  Nathan HarrisSep 12, 2025
  If your HySecurity Gate Opener has no AC power, turn on the AC power switch or connect the power to the operator. Reset the operator circuit breaker or connect power to the AC switch. Reset the circuit breaker at the electrical panel. If problems persist, have a licensed electrician check the wiring.

HySecurity SlideSmart DC 15 Specifications

General

Operating Temperature	-13°F to 158°F (-25°C to 70°C)
Control Board	Smart DC Controller
Duty Cycle	Continuous
Max Gate Weight	1500 lbs
Max Gate Length	50 ft (15.2 m)
Motor Type	DC
Control Options	Keypad, Loop Detector
Safety Features	Obstruction Sensing

Related product manuals

Preview: HySecurity SlideSmart DCS 15

HySecurity SlideSmart DCS 15

Preview: HySecurity SwingSmart DC 20

HySecurity SwingSmart DC 20

Preview: HySecurity StrongArmPark DC 10

HySecurity StrongArmPark DC 10

HySecurity StrongArmPark DC 14

HySecurity SlideDriver 40

Preview: HySecurity SlideDriver 15

HySecurity SlideDriver 15

HySecurity SlideDriver 30F

HySecurity SlideDriver 50VF2/3

Preview: SlideDriver 50 VF Series

SlideDriver 50 VF Series

HySecurity HyNet SFP 4/1

HySecurity StrongArmPark DCS 14

HySecurity Smart Touch