EasyManua.ls Logo

HySecurity SwingSmart DC 20 - User Manual

HySecurity SwingSmart DC 20
134 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
HySecurity
SwingSmart DC 20 Gate Operator
SwingSmart DCS 20 Gate Operator
Installation and Maintenance Manual
D0149 - Revision C
Installation and Maintenance Manual
(19 October 2010)
HySecurity
Corporate Headquarters
6623 S 228th Street
Kent, WA 98032

Table of Contents

Other manuals for HySecurity SwingSmart DC 20

Preview: Installation And Reference Manual
Installation And Reference Manual122 pages

Questions and Answers

  • J
    Jamie DavidAug 20, 2025
    What to do if my HySecurity Gate Opener shows 'No AC Input Power Advisory'?
    • R
      ryan16Aug 20, 2025
      If your HySecurity Gate Opener displays a 'No AC Input Power Advisory', it could be due to a shut-off or disconnected AC power source. Ensure the AC power switch is on, or connect the power to the operator. You can also try resetting the operator circuit breaker or the circuit breaker at the electrical panel. If problems persist, consult a licensed electrician to inspect the wiring.
  • D
    Dustin CaseyAug 22, 2025
    What does 'Safe Mode Alert' mean on my HySecurity SwingSmart DC 20 and how to fix it?
    • T
      Tyler QuinnAug 22, 2025
      A 'Safe Mode Alert' on your HySecurity Gate Opener indicates that either the edge sensor or inherent sensor has been activated. Start by removing any obstructions that may be triggering the sensor. If the problem continues, try adjusting the IES sensitivity or correcting the gate hardware. Also, inspect the edge sensor for faults and consider replacing worn motor brushes, if needed.
  • D
    dennisperryAug 25, 2025
    What to do if my HySecurity SwingSmart DC 20 battery is disconnected?
    • L
      Lisa CoxAug 25, 2025
      If your HySecurity Gate Opener indicates a disconnected battery, it means the batteries are not connected, or there is a wiring fault. Ensure the red wire in the upper left corner of the electrical box is securely connected to the switch.
  • J
    Joshua GrimesAug 26, 2025
    Why is my HySecurity SwingSmart DC 20 showing a 'Dead Battery' alert?
    • D
      diazjessicaAug 26, 2025
      A 'Dead Battery' alert on your HySecurity Gate Opener means the battery voltage has dropped below 21 Volts. Check the condition of the battery to resolve this issue.
  • T
    Todd HarperAug 28, 2025
    What does 'Excess Drift' mean on my HySecurity Gate Opener?
    • R
      Ricardo OrtizAug 28, 2025
      Excess Drift occurs when the Smart DC Controller detects an active loop for more than 5 minutes. To address this, check the traffic patterns at the site.
  • G
    gwarnerAug 30, 2025
    What does 'Communication Error with HY-5A' mean on my HySecurity SwingSmart DC 20 Gate Opener and how to fix it?
    • M
      Michael CabreraAug 30, 2025
      A 'Communication Error with HY-5A' on your HySecurity Gate Opener typically results from the removal of the HY-5A or a poor connection. Remove and then reinstall the HY-5A, and then press the RESET button.
  • A
    abbottlisaSep 1, 2025
    How to fix HySecurity Gate Opener with no AC power?
    • A
      Alyssa HarrisonSep 1, 2025
      If your HySecurity Gate Opener has no AC power, try the following: turn the AC power switch on or connect power to the operator, reset the operator switch, or reset the circuit breaker at the electrical panel. If these steps don't work, have a licensed electrician check the wiring.
  • N
    nathan16Sep 3, 2025
    What to do if HySecurity Gate Opener has extremely low UPS batteries?
    • S
      Shirley MillerSep 3, 2025
      If your HySecurity Gate Opener has extremely low UPS batteries and no automatic operation, replace the UPS batteries.
  • L
    Loretta LaraSep 5, 2025
    Why is my HySecurity Gate Opener in Safe Mode?
    • J
      Joshua TaylorSep 5, 2025
      Your HySecurity Gate Opener might be in Safe Mode due to an Open or Stop command from a push-button control, pressing the red button on the side of the operator, or pressing the RESET button below the display.
  • D
    Daniel SmithSep 7, 2025
    What to do for a communication error on a HySecurity Gate Opener?
    • L
      Laurie BrownSep 7, 2025
      To address a communication error on your HySecurity Gate Opener, try pressing the RESET button. If that doesn't work, remove and reinstall the HY-5A. If the problem persists, consider replacing the HY-5A.

Summary

Introducing SwingSmart DC

Intelligent Features: Smart DC Controller

Details advanced capabilities, including automatic synchronization and IES.

Safety Requirements

Essential Safety Instructions & Standards

Crucial safety guidelines, standards, and responsibilities for installers and users.

Hazard Awareness and Protection Measures

Covers hazardous materials, entrapment sensors, and usage class definitions.

Emergency Operation and Safety Symbols

Instructions for emergency stop/release and industrial safety symbols.

Chapter 1: Installation

Site Preparation and Operator Mounting

Site overview, pad condition, unpacking, and mounting the gate operator.

Gate Bracket and Arm Assembly

Attaching gate brackets, stub arms, linkage arms, and completing the assembly.

Limit Switches and Taper Clamp Adjustment

Procedures for setting limit switches and adjusting the taper clamp.

Specific Installation Options

Details for articulating arm, vent plug removal, and other installation specifics.

Chapter 2: Power

Electrical Grounding and AC Power Wiring

Proper installation of earth ground and wiring AC power (115/230V).

DC Power and Solar System Integration

Connecting DC power and considerations for solar-powered operators.

DC-Powered Operator Considerations

Important factors for operating and maintaining DC-powered systems, including battery backup.

Chapter 3: Display and Menu Options

Initial Setup and Controller Modes

Covers initial setup, controller modes, and button functions.

User Menu Configuration

Adjusting close timer, time/date, AC power loss function, and display contrast.

Installer Menu Configuration

Advanced settings for gate speed, IES sensitivity, and system defaults.

Chapter 4: Smart DC Controller

Controller Overview and Connections

Details the controller board, its inputs, and power supplies.

Vehicle Detector and Accessory Connections

Installation of vehicle detectors and various accessory devices.

Chapter 5: Bi-parting Gate Systems

Master;Slave Operator Setup

Wiring and configuration for dual-operator (master/slave) gate systems.

Chapter 6: Reference

Accessory Installation and Configuration

Guides for radio receivers, gate locks, vehicle/photo eye sensors.

Troubleshooting Smart DC Controller Issues

Diagnosing and resolving common alerts, faults, and errors.

System Schematics

Electrical diagrams for SwingSmart DC 20 and DCS 20 models.

General Maintenance

Software Tools and System Settings

Using S.T.A.R.T. software and setting user account controls.

Mechanical Component Maintenance

Routine checks for drive belts, motors, and batteries.

SWINGSMART PARTS

SwingSmart Parts List

Catalog of available replacement parts with part numbers.

LIMITED WARRANTY

SWINGSMART DC SPECIFICATIONS

HySecurity SwingSmart DC 20 Specifications

General IconGeneral
Power Supply24V DC
Max Gate Length20 ft
Control BoardSmart DC Controller
Motor TypeDC motor
Warranty5 years
Maximum Opening Angle110 degrees
Control OptionsRemote control, keypad, loop detector

Related product manuals