EasyManua.ls Logo

HySecurity StrongArmPark DCS 14 User Manual

Default Icon
82 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Programming and Operations Manual
StrongArmPark DC
™
DC 10, DCS 10, DC 14, DCS 14
Pad-mounted electromechanical barrier arm operator with
Smart DC Controller
800-321-9947 • www.hysecurity.com

Table of Contents

Questions and Answers:

HySecurity StrongArmPark DCS 14 Specifications

General IconGeneral
BrandHySecurity
ModelStrongArmPark DCS 14
CategoryGate Opener
LanguageEnglish

Summary

Welcome to HySecurity

Contact Information

Provides contact details for HySecurity distributors and technical support.

Notices and Bulletins

Supplemental Documents

Lists additional resources like manuals, software guides, and technical bulletins.

Hazardous Materials and Proper Disposal

Guidelines for handling and disposing of hazardous waste materials.

Important Safety Information

Safety - Additional Installer Responsibility

Details installer duties for safe gate operator installation and compliance.

Safety - Installer's Responsibility, continued

Further responsibilities for installers, including user demonstrations.

Safety - Owner/User Responsibility

Outlines the responsibilities of the gate operator owner and users.

Gate Operator Category and Usage Class

Secondary Entrapment Protection

Wind Load Factors & Site Prep

Manual Release

Instructions on how to manually operate the gate.

Breakaway Arm Feature

Dynamic Reversing Sensor

Explanation of the dynamic reversing sensor and its function.

Safety Notices

Common Industrial Symbols

Explanation of common safety symbols used in the manual.

Power

Installing the Earth Ground

Procedures for installing earth ground for safety and performance.

Wiring AC Power

Guidelines for connecting the operator to AC power sources.

Wiring 115VAC Power

Specific instructions for connecting 115VAC power.

Wiring 208/230VAC Power

Specific instructions for connecting 208/230VAC power.

Connecting DC Power

Steps for connecting the DC power supply.

Turning the Power Switch ON

Procedure for powering up the gate operator.

Display & Menu Options

Initial Setup

Steps for initial programming and setup after installation.

Understanding the Display and Keypad

Overview of the controller display and keypad functions.

Menu Mode Navigation

Guide to navigating through the operator's menu system.

Run Mode

Description of the operator's normal running mode.

Viewing Operator Status Displays

How to view current operator status and configuration.

User Menu

Installer Menu

Setting the Time and Date

Procedure for setting the operator's internal clock.

Resetting Open and Close Limits

How to reset and relearn the gate's open and close limits.

Learn Open and Close Limits

Detailed steps for learning the gate's open and close limits.

Test the Operator

Procedure for testing the gate operator after installation.

Setting the Close Timer

Configuration of the automatic gate closing timer.

SDC Inputs & Wiring

Overview of the Smart DC Controller

Introduction to the Smart DC Controller board and its functions.

Integrating with Security Systems

Connecting gate operators to central security systems via RS-485.

Smart DC Controller Inputs

Explanation of the various input terminals on the controller.

SDC Terminal Inputs

Mapping of terminal labels to their common uses.

Connecting Accessory Devices

Guidelines for wiring external accessories like sensors and controls.

User Relays - Programming Procedure

Procedure for programming the controller's output relays.

Revenue Control Parking Applications

Configuration options for parking lot revenue control.

Vehicle Detector Logic

Configuring how vehicle detectors influence gate operation.

Vehicle Detector Installation: HY-5A

Instructions for installing the HySecurity HY-5A vehicle detector.

Installing Standard 11-Pin Box Type Vehicle Detectors

Procedure for installing standard 11-pin box type vehicle detectors.

Photo Eyes (Non-Contact) Installation

Steps for installing photo eye sensors for safety.

Photo Eye Alignment

Guidance on aligning photo eyes for optimal performance.

Troubleshooting

System Diagnostic Messages

Understanding system alerts, faults, and errors.

Adjusting the Dynamic Reversing Sensor

Procedure for adjusting the sensitivity of the dynamic reversing sensor.

Conditions Affecting the Dynamic Reversing Sensor

Factors that can influence the dynamic reversing sensor's performance.

StrongArmPark DC Wiring Schematics

StrongArmPark DC Wiring Schematics - Solar

Wiring diagrams specific to solar-powered gate operators.

General Maintenance

Smart Touch Analyze and Retrieve Tool (S.T.A.R.T.)

Using the S.T.A.R.T. software for diagnostics and configuration.

Software Maintenance

Instructions for updating and maintaining the operator software.

Electrical Controls

General maintenance tips for electrical components.

Clock Battery Replacement

Procedure for replacing the internal clock backup battery.

Fuse Replacement

Instructions for replacing the main control system fuse.

HyProtect™ Breakaway Arm Mount

Information on replacing fasteners for the breakaway arm mount.

Mechanical Maintenance

Routine checks and upkeep for mechanical components.

Drive Belt Tension and Alignment

Procedure for checking and adjusting drive belt tension.

DC Battery Replacement

Steps for replacing the DC batteries in the operator.

Reference

Handing Change

Procedure for changing the gate operator's handing configuration.

Spring & Physical Stop Lever Assembly

Adjusting the spring and physical stop lever assembly.

Set Handing

Configuring the gate handing through the Smart DC Controller.

StrongArmPark DC Center Loop Layout

Diagram illustrating the proper placement of vehicle loops.

StrongArmPark DC Center Loop Configuration

Instructions for connecting vehicle loops to the controller.

StrongArmParkDC Loop Layout

Diagram for sequencing gates using loop layouts.

Limited Warranty

Specifications

Related product manuals