I-Tech Bluetooth Virtual Keyboard

Questions and Answers

J
Jennifer MitchellAug 17, 2025
What to do if my I-Tech Bluetooth Virtual Keyboard is on but no image appears?
- B
  Bridget ThompsonAug 17, 2025
  If your I-Tech Keyboard is on but there's no image, several factors could be at play. First, ensure the device is adequately charged and charge it if necessary. Overheating can also cause this issue, so move the device to a cooler spot and give it a few minutes. Also, make sure the keyboard rests on a firm, flat surface, ensuring the micro-switch is fully pressed. Lastly, a stuck micro-switch might be the culprit; try cleaning it.
J
Joseph EvansAug 20, 2025
Why does my I-Tech Bluetooth Virtual display multiple or erroneous keys?
- P
  Paul PaulAug 20, 2025
  If your I-Tech Keyboard displays multiple or wrong keys when typing, it might be due to the detection sensitivity being too high. Try lowering the detection sensitivity setting. Also, make sure the device is resting on a firm, flat surface.
T
theresagarnerAug 22, 2025
How to fix I-Tech Bluetooth Virtual when few keys are detected?
- P
  pbriggsAug 22, 2025
  If your I-Tech Keyboard is connected but few keys are detected, the detection sensitivity might be too low. Try raising the detection sensitivity setting.
M
Mark LawrenceAug 26, 2025
What to do if my I-Tech Keyboard doesn’t emit sounds?
- L
  Linda GonzalezAug 26, 2025
  If your I-Tech Keyboard doesn’t make sounds when you press a key, it might be because sound effects are disabled on your PalmOS5 device. To fix this, enable sound effects in the device settings under Preferences > System Sound.
V
Valerie MeyerAug 27, 2025
What to do if my I-Tech Bluetooth Virtual Keyboard is turned on but no image appears?
- J
  Jerry SmithAug 28, 2025
  If your I-Tech Keyboard is turned on but no image appears, it could be due to several reasons: * The device may not be charged: In this case, charge the device. * The device may be overheated: Move the device to a cooler location and wait a few minutes. * The device is not resting on a firm flat surface: Reposition the device to a firm surface and verify that the micro-switch is fully depressed. * The micro-switch is stuck: Clean the micro-switch.
A
Aaron HernandezAug 30, 2025
Why does my I-Tech Bluetooth Virtual not connect after the first connection? Blue LED flashes.
- A
  Amber SmithAug 31, 2025
  If, after the first connection, your I-Tech Keyboard does not connect and the blue LED flashes on and off every 2-3 seconds, it might be because your Pocket PC device is not set up to accept incoming connections. To solve this, check your Pocket PC Bluetooth Settings and make sure that Inbound and Outbound are checked.
Q
qstewartSep 2, 2025
What to do if my Pocket PC doesn’t accept the authentication of my I-Tech Keyboard while pairing?
- J
  johnsoncarrieSep 2, 2025
  If your Pocket PC doesn’t accept the authentication of your I-Tech Keyboard while pairing, it's likely that the matching passkey is not being entered correctly on both the Pocket PC and the virtual keyboard. To fix this, restart the device pairing process to re-enter the matched passkey.
S
seanjonesSep 5, 2025
Why is my I-Tech Bluetooth Virtual displaying multiple or erroneous keys when typing?
- N
  nicoleestradaSep 5, 2025
  If when typing, multiple or erroneous keys are displayed in addition to the ones you have pressed on your I-Tech Keyboard, there are a couple of potential causes: * The detection sensitivity setting is too high: Lower the detection sensitivity setting and try again. * The device is not resting on a firm flat surface: Reposition the device to a firm surface.
W
walter04Sep 8, 2025
How to fix if my I-Tech Bluetooth Virtual Keyboard is connected, but few keys are being detected?
- C
  Charles PotterSep 8, 2025
  If your I-Tech Keyboard is connected, but few or no keys are being detected, the detection sensitivity may be too low. Try raising the detection sensitivity setting and test it again.
A
Anna HuertaSep 12, 2025
What to do if my Pocket PC doesn’t emit key taps when pressing a key on my I-Tech Bluetooth Virtual Keyboard?
- T
  Timothy RamosSep 12, 2025
  To resolve the issue where your Pocket PC doesn’t emit key taps when pressing a key on your I-Tech Keyboard, ensure that 'Sound affects on Virtual Keyboard' is enabled in the VKB driver. Also, verify that your Pocket PC Sounds Notifications are set for taps.