11
REMOTE CONTROL
Remote control (CI-V) information
D Command table
Cmd�
Sub cmd� Data Description
1A* 05 KEYER > CW-KEY SET
02 34 00/01
Send/read Side Tone Level Limit setting
(00=OFF, 01=ON)
02 35 01 ~ 60
Send/read Keyer Repeat Time setting
(01=1sec ~ 60=60sec)
02 36 28 ~ 45 Send/read Dot/Dash Ratio setting
( 28=1:1:2�8 ~ 45=1:1:4�5
in 0�1 steps)
02 37 00 ~ 03 Send/read Rise Time setting
( 00=2ms, 01=4ms,
02=6ms, 03=8ms)
02 38 00/01 Send/read Paddle Polarity setting
(00=Normal, 01=Reverse)
02 39 00 ~ 02 Send/read Key Type setting
(00=Straight, 01=Bug, 02=Paddle)
02 40 00 ~ 02
Send/read MIC Up/Down Keyer setting
( 00=OFF, 01=ON (UP/DOWN),
02=ON (A/B))
DECODE > RTTY DECODE SET
02 41 00 ~ 03
Send/read the FFT Scope Averaging
setting
(00=OFF, 01=2, 02=3, 03=4)
02 42 See p� 21� Send/read the FFT Scope
Waveform Color setting
02 43 00/01
Send/read the Decode USOS setting
(00=OFF, 01=ON)
02 44 00/01
Send/read the Decode New Line
Code setting
(00=OFF, 01=ON)
02 45 00/01
Send/read the TX USOS setting
(00=OFF, 01=ON)
02 46 See p� 21�
Send/read the Font Color (Receive)
setting
02 47 See p� 21�
Send/read the Font Color (Transmit)
setting
DECODE > RTTY DECODE LOG
02 48 00/01 Send/read the Decode Log setting
(00=OFF, 01=ON)
02 49 00/01 Log Set >
Send/read the File Type setting
(00=Text, 01=HTML)
02 50 00/01 Log Set >
Send/read the Time Stamp setting
(00=OFF, 01=ON)
02 51 00/01
Log Set >
Send/read the Time Stamp (Time) setting
(00=Local, 01=UTC)
02 52 00/01 Log Set >
Send/read the Time Stamp
(Frequency) setting
(00=OFF, 01=ON)
RECORD > Recorder Set
02 53 00/01
Send/read the TX REC Audio setting
(00=Direct, 01= Monitor)
02 54 00/01 Send/read the RX REC Condition
setting
(00=Always, 01=Squelch Auto)
02 55 00/01 Send/read the File Split setting
(00=OFF, 01=ON)
Cmd�
Sub cmd� Data Description
1A* 05 RECORD > Recorder Set
02 56 00/01
Send/read the PTT Auto REC setting
(00=OFF, 01=ON)
02 57 00 ~ 03 Send/read the PRE-REC for PTT
Auto REC setting
( 00=OFF, 01=5sec,
02=10sec, 03=15sec)
RECORD > Player Set
02 58 00 ~ 03 Send/read the Skip Time setting
( 00=3sec, 01=5sec,
02=10sec, 03=30sec)
SCAN > SCAN SET
02 59 00/01
Send/read the SCAN Speed setting
(00=Slow, 01=Fast)
02 60 00/01
Send/read the SCAN Resume setting
(00=OFF, 01=ON)
02 61 00 ~ 10 Send/read the Pause Timer setting
( 00=2sec ~ 09=20sec in 2 seconds,
10=HOLD)
02 62 00 ~ 06
Send/read the Resume Timer setting
(00=0sec ~ 05=5sec, 06=HOLD)
02 63 00 ~ 04 Send/read the Temporary Skip
Timer setting
( 00=5min, 01=10min, 02=15min,
03=While Scanning,
04=While Powered ON)
02 64 00/01
Send/read the MAIN DIAL Operation
(SCAN) setting
(00=OFF, 01=Up/Down)
GPS
02 65 00/01 GPS Set >
Send/read the Position Input setting
(00=Internal GPS, 01=Manual)
02 66 00/01
GPS Set > GPS Option >
Send/read the SBAS setting
(00=OFF, 01=ON)
02 67 00/01 GPS Set > GPS Option >
Send/read the GLONASS setting
(00=OFF, 01=ON)
02 68 00/01 GPS Set > GPS Option >
Send/read the Satellite Information
Out setting
( 00=
GPS/QZSS/GLONASS,
01=GPS Only)
02 69 See p� 21� GPS Set >
Send/read the Manual Position setting
02 70 00 ~ 02
Send/read the GPS TX Mode setting
(00=OFF, 01=D-PRS, 02=NMEA)
GPS > GPS TX Mode > D-PRS
02 71 See p� 19�
Send/read the Unproto Address setting
(Up to 56 characters)
02 72 00 ~ 03 Send/read the TX Format setting
( 00=Position, 01=Object,
02=Item, 03=Weather)
GPS > GPS TX Mode > D-PRS > TX Format > Position
02 73 00 ~ 03 Send/read the Symbol setting
( 00=No�1, 01=No�2,
02=No�3, 03=No�4)
02 74
See pp� 19
and 21�
Send/read the Symbol No�1 setting
(2 characters)
To Next Page
Loading...
