Icom IC-FR3000 Remote Control Manual

8
REMOTE CONTROL OPERATION
1
DD
RX Unit OFF (0009 Default)
This command is available from the phone line
only. This explanation shows the step by step oper-
ation. You can carry out the command operation
either step by step, or by entering the password and
command continuously.
q Dial the phone number of the phone line that the
repeater is connected to.
w When the connection has been confirmed, enter
the programmed password.
Code:
∗ 0001#
• Verify the repeater replies “System Password OK
ACK (1111).”
• If the repeater replies “NG ACK (4040),” make sure
the password, header tone and de-limiter tone are
correct, and try again.
e Enter the “RX Unit OFF” command within 10 sec.
Code: ∗ 0009#
• Verify the repeater replies “OK ACK (3333).”
• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:
∗ 0001#0009#).
• The repeater turns the RX unit (front end) OFF.
r Hang up the phone, the repeater automatically
disconnects the phone.
DD
RX Unit ON (0010 Default)
This command is available from the phone line
only. This explanation shows entering the password
and command continuously. You can carry out the
command operation either step by step, or by enter-
ing the password and command continuously.
q Dial the phone number of the phone line that the
repeater is connected to.
w When the connection has been confirmed, enter
the following DTMF code.
Code:
∗ 0001#0010#
• Verify the repeater replies “OK ACK (3333).”
• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and RX
Unit ON code are correct, and try again.
• The repeater turns the RX unit (front end) ON.
e Hang up the phone, the repeater automatically
disconnects the phone.
DD
TX/RX Unit OFF (0011 Default)
This command is available from the phone line
only. This explanation shows entering the password
and command continuously. You can carry out the
command operation either step by step, or by enter-
ing the password and command continuously.
q Dial the phone number of the phone line that the
repeater is connected to.
w When the connection has been confirmed, enter
the following DTMF code.
Code:
∗ 0001#0011#
• Verify the repeater replies “OK ACK (3333).”
• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and TX/RX
Unit OFF code are correct, and try again.
• The repeater turns the TX/RX units OFF.
e Hang up the phone, the repeater automatically
disconnects the phone.
DD
TX/RX Unit ON (0012 Default)
This command is available from the phone line
only. This explanation shows the step by step oper-
ation. You can carry out the command operation
either step by step, or by entering the password and
command continuously.
q Dial the phone number of the phone line that the
repeater is connected to.
w When the connection has been confirmed, enter
the programmed password.
Code:
∗ 0001#
• Verify the repeater replies “System Password OK
ACK (1111).”
• If the repeater replies “NG ACK (4040),” make sure
the password, header tone and de-limiter tone are
correct, and try again.
e Enter the “TX/RX Unit ON” command within 10
sec.
Code:
∗ 0012#
• Verify the repeater replies “OK ACK (3333).”
• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:
∗ 0001#0012#).
• The repeater turns the TX/RX units ON.
r Hang up the phone, the repeater automatically
disconnects the phone.
OPERATION EXAMPLE (Continue)

Icom IC-FR3000 Specifications

General

Brand	Icom
Model	IC-FR3000
Category	Repeater
Language	English