How to unlock channels on Icom IC-M36 Transceiver?
If the displayed channel on your Icom Transceiver cannot be changed, the lock function may be activated. To deactivate it, hold down the [Hi/Lo] button for 1 second.
Why is there no sound from my Icom Transceiver speaker?
There might be several reasons for the lack of sound from your Icom Transceiver's speaker. First, the squelch level could be set too high; try adjusting it to the threshold point. Second, the volume level might be too low; increase it to a suitable level. Finally, if the speaker has been exposed to water, drain the water from it.
How to fix an Icom IC-M36 Transceiver that does not turn on?
If your Icom Transceiver does not turn on, it could be due to a couple of reasons. The battery might be exhausted, in which case you should recharge the battery pack. Alternatively, the battery pack might not be attached correctly, so ensure it is properly attached.
Why can't I transmit or select high power on my Icom Transceiver?
If you're unable to transmit or select high power on your Icom Transceiver, consider these possibilities: Some channels are designated for low power or receive-only, so try changing channels. The battery may be exhausted, necessitating a recharge. Ensure the battery voltage is correct, as an overcharged battery can cause issues. Finally, check if the output power is set to low; if so, push [Hi/Lo] to select high power.
What to do if the displayed channel cannot be changed on Icom IC-M36 Transceiver?
If you cannot change the displayed channel on your Icom Transceiver, the lock function might be activated. To cancel this function, push and hold [Hi/Lo] for 1 second.
What does a battery voltage error mean on my Icom Transceiver?
A battery voltage error on your Icom Transceiver indicates that the connected battery pack's voltage is more than 11 V. Make sure the battery voltage is correct.
Why does scan not start on my Icom IC-M36?
If the scan function does not start on your Icom Transceiver, it may be because “TAG” channels are not programmed. Set the desired channels as “TAG” channels to resolve this.
How to turn on beeps on Icom IC-M36?
If you are not hearing any beeps from your Icom Transceiver, the beep tone function may be turned OFF. To resolve this, set the beep tone to ON (Fix Beep/User Beep) in the set mode.
Why is transmitting impossible or high power cannot be selected on my Icom IC-M36?
If your Icom Transceiver isn't transmitting or you can't select high power, there could be several reasons. First, some channels are designed for low power or are receive-only, so try changing channels. Second, the battery may be low, so recharge it. Third, ensure the battery isn't overcharged and that the voltage is correct. Finally, the output power might be set to low; push the [Hi/Lo] button to select high power.
What to do if no sound comes from the speaker of my Icom Transceiver?
If you're not hearing any sound from the speaker of your Icom Transceiver, there are a few potential causes. First, the squelch level might be set too high; adjust it to the threshold level. Second, the volume level could be too low; increase it to a suitable level. Finally, if the speaker has been exposed to water, drain the water from it.
General| Purpose | Marine Radio Service |
|---|---|
| Operating frequency | 156.025 – 157.425 MHz |
| Antenna connector type | FA-SC58V |
| Number of antenna connectors | 1 |
| Battery type | BP-252 |
| Battery life (max) | 8 h |
| Battery low indication | Yes |
| Product color | Black |
| Waterproof up to | 1 m |
| International Protection (IP) code | IP57 |
| Operating temperature (T-T) | -20 - 60 °C |
| Number of batteries included | 1 pc(s) |
Weight and Dimensions| Depth | 43 mm |
|---|---|
| Width | 62 mm |
| Height | 139.5 mm |
| Weight | 295 g |
To Next Page
