IDEC FC4A-C16R2 - Page 523

« FC4A MICROSMART USER’S MANUAL »xi
INDEX
ID quantity of inputs D8000 6-16
ID quantity of outputs D8001 6-16
modem mode 27-1
RS232C user communication 17-3
RS485 user communication 17-4
statuses at stop, reset, and restart 2-4, 2-14, 4-4
T table ASCII character code 17-28
teaching timer 22-3
telephone number 27-3, 27-4
terminal
arrangement
AC input module
2-29
analog I/O module 2-51
CPU module 2-8, 2-19
DC input module 2-26
mixed I/O module 2-41
relay output module 2-32
transistor sink output module 2-34
transistor source output module 2-37
block removing 3-5
connection 3-18
thermistor parameter 24-13
tightening torque 3-18
TIM/CNT change status 5-29
timer
accuracy
7-8
instruction using with program branching 18-2
interrupt 5-22
status M8144 6-13
or counter
as destination operand
8-5
as source operand 8-5
timer/counter
current values
5-35
preset value
changed M8124
6-12
sum check error 29-4
preset values 5-35
confirming 5-36
timing chart
disable pulse counting
20-5, 20-11
enable pulse counting 20-4, 20-10
high-speed counter 5-13, 5-14, 5-16
reversible control
disabled
20-18
with dual pulse output 20-20
with single pulse output 20-19
zero-return operation 20-27
TML, TIM, TMH, and TMS instructions 7-7
topology 28-5
transistor
output specifications CPU module
2-17
sink output module
specifications
2-33
terminal arrangement 2-34
source output module
specifications
2-36
terminal arrangement 2-37
transition of AS-Interface master module modes 28-14
transmit 17-6
bytes 17-9
completion output 17-11
data 17-7
byte count 17-12
digits 17-9
status 17-11
code 17-11
troubles at system start-up 28-13
troubleshooting 29-1
diagrams 29-7
modem communication 27-14
TTIM 22-3
two-phase high-speed counter 5-6, 5-8
TXD1 17-6
TXD2 17-6
type
list
30-7
of protection 2-55
U underflow 6-13
up counter CNT 7-10
up/down selection reversible counter CUD 7-12
upload program 2-65
user communication
cable 1C
4-2, 17-3, 17-32, 17-34, 30-5
error 17-27
code 17-27
instructions 17-1
receive instruction cancel flag 17-24
port 1 M8022 6-11
port 2 M8023 6-11
system 1-4
setup RS232C 17-3
setup RS485 17-4
user program
adjusting clock
15-6
EEPROM sum check error 29-4
execution error 29-6
execution error M8004 6-10
protection 5-25
RAM sum check error 29-5
setting calendar/clock 15-5
syntax error 29-5
writing error 29-5
user protocol 17-5
using WindLDR 28-30
V version system program D8029 6-17
very low safety voltage 28-3, 28-7
VLSV 28-3, 28-7
W watchdog timer error 29-4
week
programmer instructions
15-1
table 15-2
timer 15-1
WindLDR
clearing error codes
29-2
monitoring 29-1
programming 24-2
catch input 5-18
clock cartridge accuracy 15-7
computer link 26-2
data link 25-7
DI or EI 18-7