IN-COMMAND NCSP3CM

Questions and Answers:

S
Sharon SheaAug 3, 2025
How to troubleshoot IN-COMMAND Measuring Instruments Display Commander (DC) when it will not turn ON?
- J
  Jerry TaylorAug 3, 2025
  If the IN-COMMAND Measuring Instruments Display Commander (DC) won't turn on or the front panel isn't working, try these steps: * First, check for +12VDC on the Positive (+) input at the back of the DC. * Next, verify there is Ground on the Negative (-) input, also on the back of the DC. * Then, inspect the fuse in the Distribution Panel. * Finally, attempt to cycle the power using the power button.
L
lmclaughlinAug 7, 2025
What to do if there is no power to the IN-COMMAND Measuring Instruments Body Control Module (BCM)?
- L
  Linda CollinsAug 7, 2025
  If there is no power to the IN-COMMAND Measuring Instruments Body Control Module (BCM), verify the following: * Check for +12VDC on pin 90. * Check for Ground on pin 86. * Check the fuse in the Distribution Panel.
A
Amy RushAug 11, 2025
Why is my IN-COMMAND Measuring Instruments DC screen flashing on and off after installation?
- J
  Jeffery HuertaAug 12, 2025
  If the IN-COMMAND Measuring Instruments DC screen is flashing after installation, follow these steps: 1. Disconnect the power wires from the back of the DC. 2. Turn off all power to both the DC and BCM. 3. Reconnect the power wires to the DC. 4. Restore power to the DC and BCM. 5. Press the Reset button on the BCM.
D
Deborah McdowellAug 16, 2025
What to check if awnings do not move using IN-COMMAND Measuring Instruments?
- B
  bsimmonsAug 16, 2025
  If the awnings aren't moving with your IN-COMMAND Measuring Instruments, check for +12VDC on Pin 88 and make sure the relay activates.
S
Shannon TaylorAug 20, 2025
What to check if slide rooms do not move using IN-COMMAND Measuring Instruments?
- E
  Emma BarrAug 21, 2025
  If the slide rooms are not moving with your IN-COMMAND Measuring Instruments, check for +12VDC on Pin 89. Ensure the relay activates.
D
Daisy ThompsonAug 25, 2025
What does it mean if IN-COMMAND Measuring Instruments DC shows 0V and no functions activate?
- J
  Jessica SmithAug 26, 2025
  If the IN-COMMAND Measuring Instruments DC shows 0V and no functions are activating, check the RV-C cable for shorts and inspect the connection for loose pins.
D
Dr. Cody RomeroAug 29, 2025
What to do if relay not activating in IN-COMMAND Measuring Instruments?
- B
  Brandon StoneAug 29, 2025
  If a relay is not activating in your IN-COMMAND Measuring Instruments system, replace it with a relay from an unused circuit. Refer to the label on the BCM cover for relay identification.

IN-COMMAND NCSP3CM Specifications

General

Brand	IN-COMMAND
Model	NCSP3CM
Category	Measuring Instruments
Language	English

Summary

Important Safety Information

Safe Operation and Environment Guidelines

Key safety instructions for operation, including driving, adult use, moisture, and substance influence.

Accessory Usage and Prohibitions

Recommendations for using approved accessories and warnings against prohibited operations.

Introduction to iN-Command System

System Features and Capabilities

Overview of the iN-Command system's extensive control and monitoring features.

User Precautions and Guidelines

Essential precautions for proper use, including power supply and service.

Packing List and Contents

Details of the items included in the product package.

iN-Command Installation Process

Tools and Supplies for Installation

List of necessary tools and supplies for a successful iN-Command installation.

Mounting the Display Commander

Step-by-step instructions and diagrams for installing the Display Commander unit.

Wiring and System Connections

Body Control Module (BCM) Wiring Diagram

Comprehensive diagram detailing all wiring connections for the Body Control Module.

System Layout and Menu Navigation

RV-C System Architecture Overview

Visual representation of the RV-C system layout and component connections.

Setup Menu List and Options

Guide to navigating the system's setup menus and available configuration options.

Travel Lockout Safety Feature

Understanding Travel Lockout Operation

Explanation of how the Travel Lockout feature enhances safety during transit.

System Controls and Component Functions

Manual Override Switch Operation

Instructions for using manual override switches for various system components.

Display Commander Button Functions

Description of the power and navigation buttons on the Display Commander.

Technical Specifications and Regulatory Information

Device Technical Specifications

Detailed specifications for the Display Commander and Body Control Module.

FCC Notes and Compliance

Important notices regarding FCC regulations and RF exposure.

System Security and Settings Management

Passcode Protection Configuration

Steps to set up, change, or clear the system passcode for security.

Panic Warning Functionality

How to activate and disengage the panic warning feature.

General Settings and Customization

Overview of the main settings menu for customizing system behavior.

Text Editing for System Functions

Procedure for editing text labels associated with system functions.

Customizing System Interface and Lists

Editing Text Labels on the DC

Detailed guide on how to modify text labels for system functions via the DC.

Scroll List Editing Procedures

Instructions for reordering or managing items within system scrollable lists.

Advanced System Configuration Options

Configuring System Triggers

How to add and set up programmable triggers with momentary or latch modes.

Selecting Generator Fuel Type

Procedure to select the appropriate fuel type for the generator.

Alarm Input Setup and Management

Steps for adding and configuring alarm inputs for system monitoring.

Passcode Timer Settings

Setting the Passcode Activation Timer

How to configure the idle time before the system automatically prompts for a passcode.

Passcode Management Functions

Changing the System Passcode

Step-by-step process to change the current system passcode.

Clearing the System Passcode

Instructions on how to remove the existing system passcode.

Resetting All System Settings

Procedure to perform a full system reset, returning to factory defaults.

Mobile Device Connectivity

Pairing iOS and Android Devices

Guide to connecting your mobile devices via Bluetooth to the iN-Command system.

iOS Mobile Device Pairing

Enabling Bluetooth on iOS Devices

Steps to activate Bluetooth functionality on an iOS device for pairing.

Pairing iOS Device to Display Commander

Detailed instructions for establishing a Bluetooth connection between iOS and the DC.

Android Mobile Device Pairing

Scanning for Unpaired Android Devices

How to scan for and identify available Android devices for pairing.

Confirming Bluetooth Pairing Request

Process for confirming pairing requests on both the DC and the Android device.

Loading DC Floor Plan Data

RV Sync for Floor Plan Updates

Procedure to sync and load floor plan configurations from the DC or via Bluetooth.

System Language and Bluetooth Session Management

Selecting System Language

How to choose the preferred language for the iN-Command system interface.

Managing Active Bluetooth Sessions

Steps to view and disconnect active Bluetooth connections.

HVAC System Controls

Vent Fan Operation and Speed Control

How to open, close, and adjust the fan speed for vent fans.

Fan Only Mode Activation

Instructions for operating the HVAC system solely in fan mode.

AC Cooling Mode Configuration

Setting the desired temperature and fan speed for AC cooling.

Advanced HVAC Mode Settings

Heating Mode Operation and Source Selection

How to set heating mode, select heat source (Gas/Electric), and adjust temperature.

Auto Mode for Temperature Management

Explanation of the Auto mode's function in automatically switching between heating and cooling.

Date, Time, and HVAC Scheduling

Setting the System Date and Time

Procedure to adjust the current date and time on the iN-Command system.

Configuring HVAC Schedules

How to set start and stop times for automated HVAC operation.

Generator Control Features

Auto Generator Start Setup

Instructions for configuring and enabling the automatic generator start feature.

Generator Schedule Configuration

Setting Specific Generator Run Times

How to define custom start and stop times for generator operation.

Software and Firmware Updates

Updating System Software via USB

Step-by-step guide to update the system's software using a USB drive.

Global Connect Setup and Wi-Fi Configuration

Connecting to Wi-Fi for Cloud Access

Steps to connect the iN-Command system to a wireless network.

Creating a Cloud Account for Remote Access

Guide to registering for a cloud account to enable remote RV monitoring and control.

Floor Plan Customization and Reset

Resetting Floor Plan Settings

How to restore floor plan configurations to default or OEM settings.

Customizing Floor Plan Options

Detailed guide on customizing various system functions within the floor plan.

System Notification Settings

Customizing System Alerts and Notifications

How to configure notifications for alarms, battery levels, tank status, and temperature.

Touch Screen Calibration

Performing Touch Screen Calibration

Instructions for calibrating the touch screen for accurate input.

System Calibration and Administration

System Calibration and Parameter Adjustment

Procedures for calibrating generator hour meter, tank sensors, and other system parameters.

Troubleshooting Common System Issues

Display Commander and BCM Power Problems

Solutions for issues related to the DC not powering on or the BCM losing power.

Screen Display and Connection Troubleshooting

Guidance for resolving screen flashing issues and connection problems.

Awnings and Slide Room Operation Issues

Troubleshooting steps for awning and slide room movement problems.

Relay Activation and Signal Error Resolution

Diagnosing and fixing issues with relay activation and signal errors.

Related product manuals

IN-COMMAND NCSP3

44 pages

Table of Contents