EasyManuals Logo
Home>InFocus>Projector>IN112

InFocus IN112 User Guide

InFocus IN112
35 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #12 background imageLoading...
Page #12 background image
11
Shutting down the projector
Auto Off Time
The projector also has an Auto Off Time feature that automatically turns the
projector off after no active sources are detected and no user interaction with the
projector is performed for 30 minutes. By default, this feature is off. You can
change the length of time, see page 29.
Turning off the projector
To turn the projector off, press the Power button on the remote or keypad. The
lamp turns off and the Power LED blinks blue for 1 minute while the fans continue
to run to cool the lamp. If the Power Saving Mode feature is on and when the lamp
has cooled, the LED lights blue and the fans stop. If the Power Saving Mode feature
is off and when the lamp has cooled, the LED blinks blue and the fans stop. Unplug
the power cable to completely power off the projector.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it does
not, troubleshoot the setup.
The Status Indicator Panel on top of the projector indicates the state of the
pro
jector and can help you troubleshoot
TEMP/LAMP
POWER
.
Table 3: Status indicator light behavior and meaning
Status Indicator Light Meaning
POWER: Solid blue
POWER: Blinking blue
1. If the Power Saving Mode feature is on,
the projector is plugged in.
2. The projector is on and initialized.
3. The projector is in normal operation.
1. If the Power Saving Mode is off, the
p
rojector is plugged in.
2. The projector is powering down and
th
e fans are cooling the projector.
POWER: Blinking blue
TEMP/LAMP: Blinking pink
POWER: Solid blue
TEMP/LAMP: Blinking pink
The projector fan(s) are not operating
co
rrectly and the projector has been shut
down.
The lamp failed to ignite.
Contact Technical Support if the problem
p
ersists. Visit www.infocus.com/support
to contact service.
POWER: Solid blue
TEMP/LAMP: Blinking red
The lamp has reached its end of life and
must be replac
ed. The lamp will continue
to operate untils it fails.
Contact Technical Support. Repair may be
nee
ded.
POWER: Solid blue
TEMP/LAMP: Blinking blue
1. The projector is overheating and the
lamp will be shut
off. The fans will
continue to run.
2. The projector will not turn back on
unt
il the cooling process is complete.

Other manuals for InFocus IN112

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the InFocus IN112 and is the answer not in the manual?

InFocus IN112 Specifications

General IconGeneral
Matrix size0.55 \
Number of colors1.073 billion colors
Native aspect ratio4:3
Projection distance1.5 - 11.9 m
Projection technologyDLP
Supported aspect ratios4:3, 5:4, 16:9, 16:10
Contrast ratio (typical)4000:1
Screen size compatibility40 - 303 \
Projector native resolutionSVGA (800x600)
Keystone correction, vertical± 40 °
Vertical synchronization (max)120 kHz
Vertical synchronization (min)50 kHz
Horizontal synchronization (max)100 kHz
Horizontal synchronization (min)31 kHz
Projector brightness (economic mode)2200 ANSI lumens
FocusManual
Offset15 %
Throw ratio1.97 - 2.17:1
Zoom capabilityYes
Focal length range- mm
Lamp typeUHP
Lamp power180 W
Light source typeLamp
Lamp power (economic mode)150 W
Service life of light source5000 h
Service life of light source (economic mode)6000 h
DVI portNo
Audio (L/R) in-
USB connector typeMini-USB B
Serial interface typeRS-232
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
S-Video inputs quantity1
VGA (D-Sub) ports quantity3
Component video (YPbPr/YCbCr) in0
Supported video modes1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format systemNTSC, PAL, SECAM
Supported graphics resolutions1920 x 1200 (WUXGA)
RMS rated power2 W
PlacementDesktop, Ceiling
Product typeStandard throw projector
Product colorBlack
Cable lock slot typeKensington
Power sourceAC
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (max)260 W
Power consumption (standby)1 W
Power consumption (typical)235 W
Noise level30 dB
Preset modesBeige wall, Blackboard, Bright, Cinema, Custom, Presentation, Whiteboard
CertificationUL, c-UL, FCC, CE
Password protection typeUser
Noise level (economic mode)28 dB
On Screen Display (OSD) languagesCHI (SIMPL), CHI (TR), DAN, DEU, DUT, ENG, ESP, FIN, FRE, ITA, KOR, NOR, POL, POR, RUS, SWE, TUR
Operating altitude0 - 3048 m
Operating temperature (T-T)5 - 35 °C
Cables includedAC, VGA
Weight and Dimensions IconWeight and Dimensions
Depth235 mm
Width284 mm
Height70 mm
Weight2170 g
Package width330 mm
Package height150 mm
Package weight3670 g

Related product manuals