How to fix a reversed image on InFocus IN116 Projector?
If the image is reversed left to right on your InFocus Projector, turn off Rear Project in Advanced Menu > Setup > Image Setup... menu.
Why won't the lamp turn on and the InFocus IN116 Projector is overheating?
If the InFocus Projector is overheating and the lamp won’t turn on, ensure that the vents are not blocked. Turn off the projector and allow it to cool for one minute.
How to fix a fuzzy or cropped image on my InFocus IN116 Projector?
To correct an image that is fuzzy or cropped on your InFocus Projector, change the computer's "Resolution" setting to match the projector's resolution. This can typically be found in the Control Panel under Display settings.
What to do if only laptop background appears on InFocus IN116?
If you are only seeing your laptop’s background and not the Desktop icons on the InFocus Projector, change the Multiple Display setting to "Duplicate these displays". This setting can usually be found in the Control Panel under Display > Screen Resolution.
How to flip the image on InFocus IN116 Projector?
To resolve an upside-down image on your InFocus Projector, turn off Ceiling Mount in the Basic menu.
How to adjust colors on InFocus IN116?
If the projected colors don’t match the source on your InFocus Projector, adjust the items in the Advanced Menu > Image > Color... menu.
How to correct a not square image on InFocus IN116?
To correct the image if it is not square on your InFocus Projector, adjust the Keystone setting on the keypad.
What to do if InFocus Projector says 'Signal out of range'?
If the InFocus Projector shows "Signal out of range", press the Auto Image button on the remote. You may also need to adjust the computer refresh rate (Windows 7: Control Panel > Display > Screen Resolution > Advanced Settings > Adapter tab) and/or set a different resolution on your computer.
How to make the image sharper on InFocus IN116 Projector?
To fix an image that is not sharp on your InFocus Projector, adjust the Sharpness in the Basic Menu.
How to center the image on my InFocus IN116 screen?
To correct an image that is not centered on the screen with your InFocus Projector, move the projector and adjust the height. You can also adjust horizontal or vertical position in Advanced Menu > Previous Image > PC... menu.
General| Matrix size | 0.65 \ |
|---|---|
| Number of colors | 1.073 billion colors |
| Native aspect ratio | 16:10 |
| Projection distance | 1.41 - 9.66 m |
| Projection technology | DLP |
| Supported aspect ratios | 4:3, 5:4, 16:9, 16:10 |
| Contrast ratio (typical) | 4000:1 |
| Screen size compatibility | 45 - 303 \ |
| Projector native resolution | WXGA (1280x800) |
| Keystone correction, vertical | ± 40 ° |
| Vertical synchronization (max) | 120 kHz |
| Vertical synchronization (min) | 50 kHz |
| Horizontal synchronization (max) | 100 kHz |
| Horizontal synchronization (min) | 31 kHz |
| Projector brightness (economic mode) | 2200 ANSI lumens |
| Focus | Manual |
| Offset | 13 % |
| Throw ratio | 1.47 - 1.83:1 |
| Zoom capability | Yes |
| Focal length range | - mm |
| Lamp type | UHP |
| Lamp power | 180 W |
| Light source type | Lamp |
| Lamp power (economic mode) | 150 W |
| Service life of light source | 5000 h |
| Service life of light source (economic mode) | 6000 h |
| DVI port | No |
| HDMI version | 1.3 |
| Audio (L/R) in | - |
| USB connector type | Mini-USB B |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| S-Video inputs quantity | 1 |
| VGA (D-Sub) ports quantity | 3 |
| Component video (YPbPr/YCbCr) in | 0 |
| Supported video modes | 1080i, 1080p, 480i, 480p, 576i, 576p, 720p |
| Analog signal format system | NTSC, PAL, SECAM |
| Supported graphics resolutions | 1920 x 1200 (WUXGA) |
| RMS rated power | 2 W |
| Placement | Desktop, Ceiling |
| Product type | Standard throw projector |
| Product color | Black |
| Cable lock slot type | Kensington |
| Power source | AC |
| Power consumption (max) | 260 W |
| Power consumption (standby) | - W |
| Power consumption (typical) | 235 W |
| Noise level | 30 dB |
| Preset modes | Beige wall, Blackboard, Bright, Cinema, Custom, Presentation, Whiteboard |
| Certification | UL, c-UL, FCC, CE |
| Noise level (economic mode) | 28 dB |
| On Screen Display (OSD) languages | CHI (SIMPL), CHI (TR), DAN, DEU, DUT, ENG, ESP, FIN, FRE, ITA, KOR, NOR, POL, POR, RUS, SWE, TUR |
| Operating altitude | 0 - 3048 m |
| Operating temperature (T-T) | 5 - 35 °C |
| Cables included | AC, VGA |
Weight and Dimensions| Depth | 235 mm |
|---|---|
| Width | 284 mm |
| Height | 70 mm |
| Weight | 2170 g |
| Package width | 330 mm |
| Package height | 150 mm |
| Package weight | 3670 g |
Complies with FCC Rules, but may cause interference if not used properly.
Compliance with Canadian ICES-003 standard for digital apparatus.
Lists agency approvals like cULus and other country-specific approvals.
Connects computer via VGA.
Connects computer via HDMI.
Connects the power cord.
Additional computer connection options.
Connects via HDMI for audio/video.
Connects via composite video cable.
Connects via VGA output from video device.
Connects via component video using adapter.
Connects via S-video cable.
Connects audio source to projector or external speakers.
Automatically turns projector off after inactivity.
Connect audio source for projector speakers.
Steps to resolve audio playback issues.
Common image and audio adjustments for the projector.
Complex settings for image, setup, and system configuration.
Instructions for cleaning the projector lens.
How to use the security lock system.
To Next Page
