Why is fault code 43 shown on my INFOSEC UPS SYSTEM E3 LCD RT IEC 800?
Fault code 43 appears, and the UPS shuts down automatically, because there is an overload at the UPS output. Remove excess loads from the UPS output and then restart the UPS.
What to do if my INFOSEC UPS SYSTEM E3 LCD RT IEC 800 is overloaded?
If the UPS is overloaded, the icon and the icon will flash on the LCD display, and the alarm will sound twice every second. To resolve this, remove excess loads from the UPS output.
What to do if fault code 14 appears on my INFOSEC UPS SYSTEM E3 LCD RT IEC 800?
Fault code 14 appears, and the alarm sounds continuously, because the UPS shut down automatically due to a short circuit on the UPS output. Check the output wiring and whether any connected devices are in a short circuit status.
Why is the battery backup time shorter than nominal value on my INFOSEC UPS SYSTEM E3 LCD RT IEC 800 UPS?
A shorter than expected battery backup time on your UPS can occur for the following reasons: * The batteries are not fully charged. Charge the batteries for at least 5 hours and then check capacity. * The batteries are defective.
Why is an icon flashing on the LCD display with alarm sounding on my INFOSEC UPS SYSTEM E3 LCD RT IEC 800?
An icon flashing on the LCD display with an alarm sounding every second indicates that either the line and neutral conductors of the UPS input are reversed, or the external or internal battery is incorrectly connected. To solve this: * Rotate the mains power socket by 180° and then connect it to the UPS system. * Check if all batteries are well connected.
What to do if there is no indication and alarm on my INFOSEC UPS SYSTEM E3 LCD RT IEC 800 UPS?
If there is no indication and alarm, even though the main power is normal, it could be due to these reasons: * The AC input power is not correctly connected. Check if the input power cord is firmly connected to the mains. * The AC input is connected to the UPS output. Plug the AC input power cord into the AC input correctly.
Why is an icon and warning code flashing on my INFOSEC UPS SYSTEM E3 LCD RT IEC 800 UPS?
An icon and a warning code flashing on the LCD display with an alarm sounding every second indicates that the EPO function is activated. To disable the EPO function, set the circuit in a closed position.
General| Product Type | Line Interactive UPS |
|---|---|
| Output Power Capacity | 800 VA / 640 W |
| Capacity | 800 VA |
| Nominal Input Voltage | 230 V |
| Nominal Output Voltage | 230 V |
| Frequency | 50/60 Hz |
| Topology | Line Interactive |
| Display | LCD |
| Operating Temperature | 0 - 40 °C |
| Humidity | 0 - 95% non-condensing |
| Output Voltage | 230 V |
| Form Factor | Tower |
| Transfer Time | 4 ms typical |
| Battery Type | Sealed Lead Acid |
| Battery Recharge Time | 4 hours to 90% |
| Communication Interface | USB |
| Protection | Overload, Short Circuit |
| Storage Temperature | -15°C to 45°C |
Details electrical hazards, user repair restrictions, and safe isolation procedures for UPS units.
Specifies compatible loads and warns against connecting incompatible devices like microwaves or laser printers.
Covers correct placement, environmental conditions, cleaning, and avoiding liquid spills near the UPS.
Emphasizes precautions for battery handling, disposal, and risks like explosion or electric shock.
Explains the CE logo indicating adherence to EMC and LVD standards for electrical equipment.
Illustrates and labels the rear panel ports and connectors across different UPS models for installation.
Step-by-step instructions for connecting battery wires and mounting the UPS in rack or tower configurations.
Guides through essential initial steps, including connecting the UPS input to a grounded receptacle.
Connect devices to outlets and communication ports (USB, RS-232, Intelligent slot) for monitoring.
Instructions for connecting network lines and configuring the Emergency Power Off (EPO) function.
Details how to connect an external battery pack for specific UPS models to extend runtime.
Guides on turning on the UPS after installation and installing necessary monitoring software.
Provides instructions for safely hot-swapping internal UPS batteries with necessary precautions.
Explains the functions of the ON/MUTE, OFF/ENTER, and SELECT buttons for controlling the UPS.
Overview of rack and tower LCD displays, detailing load, input/output, battery status, and indicators.
Details LCD readings for input/output/battery, load status, and explains audible alarm patterns.
A reference table decoding abbreviations and their meanings as shown on the UPS LCD screen.
Guides through setting output voltage, programmable outlets, LCD direction, and exiting the configuration menu.
A practical guide for navigating the UPS settings menu to configure various operational parameters.
Explains different UPS operating modes like ECO, Buck, Boost, Battery, and Standby.
Lists common UPS fault events, their codes, icons, and descriptions for troubleshooting purposes.
Describes various warning indicators, their associated icons, and the corresponding alarm sounds.
Addresses issues where the UPS shows no indication or alarm when the mains power is normal.
Guides on troubleshooting EPO function activation and site wiring faults causing alarms.
Solutions for problems related to battery connection, high voltage, or low voltage issues.
Provides steps to resolve UPS overload conditions and output short circuits.
Covers troubleshooting internal UPS faults, reduced battery backup time, and fan issues.
Notifies about battery service life limits and advises contacting the dealer for replacement.
Provides instructions for storing the UPS, including initial charge, location, and periodic recharge frequency.
To Next Page