To Next PageTo Next PageWhat to do if the Ingersoll-Rand 2000 Air Compressor is using detergent type lubricant?
If a detergent type lubricant is being used in your Ingersoll-Rand Air Compressor, drain the existing lubricant and refill with the proper lubricant.
What to do if the Ingersoll-Rand 2000 lubricant viscosity is too high?
If the lubricant viscosity of your Ingersoll-Rand Air Compressor is too high, drain the existing lubricant and refill with the proper lubricant.
What to do if the Ingersoll-Rand 2000 Air Compressor lubricant viscosity is too low?
If the lubricant viscosity of your Ingersoll-Rand Air Compressor is too low, drain the existing lubricant and refill with the proper lubricant.
What to do if the Ingersoll-Rand Air Compressor is located in damp or humid location?
If your Ingersoll-Rand Air Compressor is in a damp or humid location, relocate it or install a crankcase heater kit.
What to do if the Ingersoll-Rand 2000 Air Compressor has a clogged or dirty inlet and/or discharge line filter?
If the inlet or discharge line filter of your Ingersoll-Rand Air Compressor is clogged or dirty, clean or replace it.
What to do if Ingersoll-Rand 2000 Air Compressor has air leaks in air discharge piping?
If you notice air leaks in the air discharge piping of your Ingersoll-Rand Air Compressor, check the tubing and connections. Tighten any loose joints or replace components as required.
What to do if the Ingersoll-Rand Air Compressor valve will not close?
If the valve on your Ingersoll-Rand Air Compressor isn't closing, it could be due to: * Debris in the solenoid valve preventing the diaphragm from seating. Remove the solenoid valve, disassemble it, clean it, and then reassemble it. * A short in an electrical component. Check and replace the power cord or timer as necessary.
What to do if the Ingersoll-Rand 2000 timer will not activate?
If the timer on your Ingersoll-Rand Air Compressor isn't activating, there are several potential causes: * There may be no electrical supply - apply power. * The timer itself may be malfunctioning - replace the timer. * A port could be clogged - clean the valve. * The solenoid valve might be defective - replace the solenoid valve. * The strainer might be clogged - clean the strainer.
What to do if the Ingersoll-Rand 2000 Air Compressor lubricant level is too high?
If the lubricant level in your Ingersoll-Rand Air Compressor is too high, drain the excess lubricant.
General| Brand | Ingersoll-Rand |
|---|---|
| Model | 2000 |
| Category | Air Compressor |
| Language | English |
The Ingersoll Rand Nirvana Cycling refrigerated air dryer removes moisture, oil vapor, and other contaminants from compressed air.
The Company warrants that the equipment manufactured by it will be free of defects in material and workmanship for a period of twelve months.
Details the nomenclature of the refrigerated dryer, including model, condenser type, and power ratings.
Guidance on inspecting the unit upon receipt and safely unpacking and handling the dryer.
Essential safety precautions and warnings for operating and maintaining the air dryer.
Defines Warning, Caution, and Notice to communicate hazard severity and company policy.
Explains how the dryer removes moisture by cooling air to between 36-40°F and lists the major systems.
Describes the components of the dryer that come into contact with the compressed air.
Explains how condensate is discharged using a zero-air-loss drain with a capacitive sensor.
Details the closed-loop system handling R-404A refrigerant, including compressor, condenser, and filter dryer.
Describes the circulation of thermal mass fluid in a closed pump loop system for cooling.
Details the Microprocessor Control, its features, and access levels (CUSTOMER, TECHNICIAN, FACTORY).
Summarizes the keypad functions and displays of the Microprocessor Control.
Lists and describes the system parameters that can be accessed and displayed by the user.
Explains user-adjustable set points and lists parameters like Chiller Off Temperature.
Provides step-by-step instructions for adjusting set points in CUSTOMER MODE using the control panel.
Details various alarms detected by the Microprocessor Control and their functions.
Describes the three available start modes: Manual, Auto Restart, and Remote Automatic.
Provides guidelines for selecting an appropriate location and mounting the dryer, considering ambient temperature and clearance.
Details piping arrangements, valve functions, and recommendations for connecting the dryer.
Recommends pre-filters and post-filters for protecting the dryer and ensuring performance.
Explains how to make electrical connections, including warnings about wiring.
Provides essential notices and a warning regarding initial start-up procedures.
Outlines the step-by-step sequence for starting the dryer after power is applied.
Guide to routine maintenance tasks required for the air dryer to ensure optimal performance.
Recommends regular inspection and cleaning of the condenser, including optional ambient air filters.
Provides maintenance recommendations for the condensate discharge system, including service unit replacement.
Access to advanced parameters for technicians to adjust settings and troubleshoot the dryer.
Provides a warning and keystrokes to enter Technician Mode for parameter adjustment.
Explains how to access and view the list of the most recent 20 alarm conditions for troubleshooting.
Guide to identifying and resolving common problems encountered with the air dryer.
Introduces the troubleshooting guide designed to help identify and correct dryer malfunctions.
A guide listing common problems, their symptoms, possible causes, and corrective actions.
Presents the wiring diagram for the NVC2000-2400 Air and Watercooled models.
Shows the general arrangement of the NVC2000-2400 dryer with different views and dimensions.
Lists replacement parts for NVC2000/2400 models, including part numbers and recommended quantities.
Provides engineering specifications for air and water-cooled condensers, including ratings and dimensions.
