To Next PageTo Next PageWhat causes condensate contamination in Ingersoll-Rand Air Compressor discharge air?
If the discharge air from your Ingersoll-Rand Air Compressor is contaminated with condensate: * The aftercooler may not be functioning correctly. Clean or replace it. * The moisture separator drain trap may be faulty. Repair or replace it.
Why is pressure too high in Ingersoll-Rand Air Compressor because speed is not reducing?
If the pressure produced by your Ingersoll-Rand Air Compressor is too high because the speed isn't reducing as demand decreases: * The controller settings may be incorrect. Check and modify the settings. * The pressure transducer may be faulty, incorrectly calibrated, or not receiving a pressure signal. Recalibrate or replace it.
What to do if discharge air is contaminated with coolant in Ingersoll-Rand Air Compressor?
If the discharge air from your Ingersoll-Rand Air Compressor is contaminated with coolant: * Check if the scavenge pipe is blocked or broken, or if the o-ring is not sealing. Clean or replace as necessary. * Inspect the separator element for punctures, incorrect installation, the need for replacement, or incorrect sealing. Replace if needed. * If incorrect coolant has been added, drain the system, check for damage, clean, and refill with the correct coolant. * If the system has been overfilled with coolant, check for damage and drain the excess.
What causes high airend discharge temperature in Ingersoll-Rand Air Compressor?
High airend discharge temperature in your Ingersoll-Rand Air Compressor can be caused by: * Compressor operating above rated pressure: Check and modify settings. Review system requirements. * Low coolant level: Check for leaks and top up coolant. See also information about discharge air being contaminated with coolant. * High ambient temperature: Review installation and system parameters. * Insufficient cooling air: Check ducting and cooling air path. * Dirty, blocked coolant cooler (cooling air side): Clean or replace.
What causes Ingersoll-Rand Air Compressor discharge air to be too hot?
If the discharge air from your Ingersoll-Rand Air Compressor is too hot, it could be due to: * High ambient temperature: Review the installation and system parameters. * Insufficient cooling air: Check the ducting and cooling air path, and verify the direction of blower rotation. * Dirty, blocked aftercooler (cooling air side): Clean or replace it.
Why does my Ingersoll-Rand Air Compressor package draw too much current?
If your Ingersoll-Rand Air Compressor package is drawing too much current, consider these potential causes: * The compressor may be operating above its rated pressure. Check and adjust the settings accordingly. * A separator filter element might be dirty or blocked. Replace it.
Why is my Ingersoll-Rand Air Compressor package producing excessive noise?
Excessive noise from your Ingersoll-Rand Air Compressor package can be due to several reasons: * Ensure all panels and doors are properly closed. * Check for air leaks from internal pipework or components; repair or replace as necessary. * Inspect the blower or blower motor bearings for wear; repair or replace if needed. * Remove any loose debris impacting the blower during rotation and repair any damage. * Check if the blowdown valve is stuck open; repair or replace it. * Verify that the pressure relief valve is seating correctly; repair or replace it if not. * Look for vibration due to motor, airend, or blower imbalance; repair or replace the affected components.
Why is the discharge air from my Ingersoll-Rand R37 too hot?
If the discharge air from your Ingersoll-Rand Air Compressor is too hot, consider these potential causes: * High ambient temperature. Review the installation and system parameters. * Insufficient cooling air. Check the ducting and cooling air path, and verify the direction of blower rotation. * Dirty or blocked aftercooler (cooling air side). Clean or replace the aftercooler.
Why does my Ingersoll-Rand Air Compressor stop and not restart?
If your Ingersoll-Rand Air Compressor stops and will not restart, it could be due to: * A tripped drive controller. See Tables 4 and 5. * The controller has tripped the compressor. See Tables 4 and 5. * The maximum number of starts per hour has been exceeded.
How to troubleshoot Ingersoll-Rand R37 that will not start?
If your Ingersoll-Rand Air Compressor will not start, it could be due to several reasons: * There may be no power supply. Ensure the power is switched on. If it is, contact a qualified electrician. * There may be a controller failure. Check the supply to the controller and replace it if necessary. * There may be a starter failure. Isolate the supply, lock it off, tag it, and replace the failed component. Alternatively, contact your local Ingersoll Rand representative.
General| Brand | Ingersoll-Rand |
|---|---|
| Model | R37 |
| Category | Air Compressor |
| Language | English |
Emphasizes following all danger, warning, and caution instructions for safe operation.
Outlines electrical connection standards, grounding, and wiring best practices.
Specific electrical requirements for Variable Speed Drive compressors.
Guides on proper grounding of the compressor system according to codes.
Covers starting, stopping, warm-up, and emergency procedures for VSD operation.
Details on connecting the controller to a Modbus RTU network.
Guidelines for routing RS-485 cables and avoiding electrical interference.
Steps for setting Modbus addresses and configuring master settings for communication.
Instructions for enabling COM control and auto-restart for system integration.
