Inspur NF3120M5 - User Manual

Other manuals for Inspur NF3120M5

Installation Guide2 pages

Questions and Answers

A
Alyssa YoderAug 20, 2025
How to fix Inspur Server when local server cannot connect to MEGARAC SP-X?
- J
  Jeffrey MooreAug 20, 2025
  If your local or central server is unable to connect to the MEGARAC SP-X remote management card, try the following: 1. Ensure the network cable is properly inserted into the LAN interface. 2. Verify that the remote IP address and the local/central server IP address are in the same subnet. Test the connection by executing “Ping xx.xx.xx.xx” (the remote server IP) on the local/central server to confirm the remote server responds. 3. Check if the IP source is set to DHCP. Note that you cannot manually set the IP address if it's configured for DHCP.
J
jamie59Aug 22, 2025
What to do if Inspur Server MEGARAC SP-X cannot connect to the network in a firewall environment?
- T
  Tabitha AustinAug 22, 2025
  If the MEGARAC SP-X on your Inspur Server is unable to connect to the network due to a firewall, add the following port numbers to your firewall settings: * 5123 (virtual floppy) (TCP) * 5120 (Virtual CDROM) (TCP) * 623 (IPMI) (TCP & UDP) * 80 (HTTP) (TCP) * 7578 (iKVM) (TCP) * 443 (HTTPs) (TCP) * 161 (SNMP) (UDP)
G
gwendolyn28Aug 25, 2025
How to troubleshoot abnormal network on Inspur NF3120M5?
- J
  jenniferhaleAug 25, 2025
  To troubleshoot network issues on your Inspur Server, follow these steps: 1. Check that the network cable is properly connected and that the network LED is flashing normally. Try re-inserting the network cable. 2. If the problem persists, connect a computer directly to the server. If the direct connection works, the issue may be with the network cable or switch port. 3. If the direct connection is still not working, download the latest NIC driver.
B
Becky McdanielAug 26, 2025
What to do if there is no display after powering on Inspur Server?
- J
  john34Aug 27, 2025
  If you encounter a situation where there is no display after powering on your Inspur Server, consider the following steps: 1. First, verify that the monitor is receiving power and is turned on. 2. If the monitor is on, check the connection between the monitor and the server's VGA port to ensure it is secure. 3. Try connecting to a different monitor to rule out a monitor issue. 4. If there is still no output on the new monitor, log in to the BMC Web interface and open BMC remote KVM to check for output on the monitor. If there is normal output, the VGA port may be faulty.
J
Jessica OsborneAug 28, 2025
What to do if Inspur NF3120M5 fails to power on at startup?
- T
  Tammy HerreraAug 28, 2025
  If your Inspur Server fails to power on during startup, take these steps: a. Check the power supply: If the power module LED is lit, the power supply is normal. If the LED is off or red, check the power supply and cable connections. b. If the power supply is normal, reinsert the power module and try powering on again. c. If you have a spare power module of the same type, swap it in to test for a power module fault.
R
Robert PerezAug 30, 2025
Why are keyboard and mouse not available on Inspur NF3120M5 Server?
- S
  stephanietuckerAug 30, 2025
  If the keyboard and mouse are not working with your Inspur Server, try these steps: a. Ensure the keyboard and mouse are correctly and firmly connected. b. Test with different keyboard and mouse to rule out faulty peripherals. c. Power cycle the server and test again. d. Reboot and enter the BIOS or RAID configuration interface to test keyboard and mouse functionality outside the operating system. If they work in these interfaces but not in the OS, it could indicate a system fault. If the problem persists, it might be a motherboard interface issue.
C
Carolyn GreenSep 2, 2025
Why are Inspur NF3120M5 Server chassis fans making excessive noise?
- K
  Kelly JohnsonSep 2, 2025
  If the chassis fans of your Inspur Server are making excessive noise, consider the following: a. Check if the fans are running at high speed due to an over-temperature condition inside the chassis. b. If the chassis temperature is high, check the server room temperature. If it's too high, use air conditioning to cool the room. c. If the server room temperature is normal, inspect the front panel and chassis interior for dust accumulation or blocked air inlets. Ensure the server room environment is clean to prevent overheating. d. Determine if the server is running under a high load.
B
brandi62Sep 4, 2025
What to do if the status LED on Inspur NF3120M5 front panel is abnormal?
- T
  tracy72Sep 4, 2025
  If the status LED on the front panel of your Inspur Server is abnormal, follow these steps: a. First, identify which LED is abnormal. b. If the system failure LED is abnormal, check if the system is running normally. If it is, log in to the BMC Web interface to check the BMC logs for any reported errors. c. If the power failure LED is abnormal, check if the power module LED is normal. If it is, log in to the BMC Web interface to view the BMC logs for errors. d. If other LEDs are abnormal, check the BMC logs via the BMC Web interface for any reported errors.
C
Curtis WashingtonSep 6, 2025
Why is Inspur NF3120M5 power module LED off or red?
- P
  paige89Sep 6, 2025
  If the power module LED on your Inspur Server is off or red, try the following: a. Check all power cables to ensure they are properly connected. Re-plug them to ensure a secure connection. b. If the issue persists, try re-inserting the power module itself. c. If possible and if shutdown is allowed, swap the two power modules to determine if the fault lies with a specific module.
B
brownsherriSep 8, 2025
What does it mean if the HDD status LED is abnormal on Inspur NF3120M5?
- S
  Stephanie DuncanSep 8, 2025
  If the HDD status LED on your Inspur Server is abnormal, here’s what to check: a. If the issue was caused by manual operations, restore the array through RAID configuration. b. If there were no manual operations, verify that the HDDs are being identified correctly. If the server has a RAID card, log in to the RAID management interface to check for HDD failures.