Integra DHC-80.3 User Manual

90
En
■ Playback stops while listening to music files on
the server
■ Can’t connect to the AV controller from a Web
browser
■ Can’t access the music files on a USB device
■ Standby power consumption
■ The sound changes when I connect my
headphones
■ The speaker distance cannot be set as required
■ How do I change the language of a multiplex
source
■ The u functions don’t work
■ The functions System Off/Auto Power On and
Direct Change don’t work for components
connected via u
■ When performing “Automatic Speaker Setup”,
the measurement fails and the message
“Ambient noise is too high.” is displayed.
■ The following settings can be made for the
S-Video and composite video inputs
You must use the buttons on the unit to make these
settings.
On the AV controller, press the input selector for the
input source that you want to set and the
Setup button
simultaneously. While holding down the input selector
button, press Setup until “Video ATT:On” appears on
the display. Then, release both buttons. To reactivate
the setting, repeat the above process so that “Video
ATT:Off” appears on the display, and release the
buttons.
• Video Attenuation
This setting can be made for the BD/DVD, VCR/DVR,
CBL/SAT, GAME or AUX input.
If you have a game console connected to the composite
video input, and the picture isn’t very clear, you can
attenuate the gain.
Video ATT:Off: (default).
Video ATT:On: Gain is reduced by 2 dB.
Make sure your server is compatible with the AV
controller.
101,
103
If you download or copy large files on your
computer, playback may be interrupted. Try closing
any unused programs, use a more powerful
computer, or use a dedicated server.
—
If the server is serving large music files to several
networked devices simultaneously, the network may
become overloaded and playback may be
interrupted. Reduce the number of playback devices
on the network, upgrade your network, or use a
switch instead of a hub.
—
If you’re using DHCP, your router may not always
allocate the same IP address to the AV controller, so
if you find that you can’t connect to a server or
Internet radio station, recheck the AV controller’s IP
address on the “Network” screen.
68
Check the “Network” settings. 68
USB Device Playback
Make sure the USB device is plugged in properly. —
The AV controller supports USB devices that
support the USB mass storage device class.
However, playback may not be possible with some
USB devices even if they conform to the USB mass
storage device class.
—
USB memory devices with security functions cannot
be played.
—
Others
In the following cases, the power consumption in
standby mode may reach up to a maximum of
45 W (North American)/50 W (Others):
– You are using the Universal Port jack.
–“Network Control” is set to “Enable” in the
“Network” setting.
–“HDMI Control(RIHD)” setting is set to “On”.
(Depending on the TV status, the AV controller
will enter standby mode as usual.)
–The “HDMI Through” setting is set to other than
“Off”.
21, 67,
68
When a pair of headphones is connected, the
listening mode is set to Stereo, unless it’s already set
to Stereo, Mono or Direct.
—
In some cases, corrected values suitable for home
theater use may be set automatically.
—
Use the “Multiplex” setting on the “Audio Adjust”
menu to select “Main” or “Sub”.
56
To use u, you must make an u connection and
an analog audio connection (RCA) between the
component and AV controller, even if they are
connected digitally.
23
While Zone 2 or Zone 3 is selected, the u
functions don’t work.
23
While Zone 2 or Zone 3 is selected, the u
functions don’t work.
23
This can be caused by a malfunction in your speaker
unit. Check if the unit produces normal sounds.
—

Integra DHC-80.3 Specifications

General

Brand	Integra
Model	DHC-80.3
Category	Controller
Language	English