Integra DTR-5.1 User Manual (English)

Other manuals for Integra DTR-5.1

Questions and Answers:

J
Jordan GeorgeAug 20, 2025
Why is there power on my Integra DTR-5.1 Receiver but no sound?
- R
  robertvillegasAug 20, 2025
  There could be several reasons for this. Check if the MUTING indicator is lit and, if so, press the MUTING button on the remote to turn it off. Also, ensure the digital/analog input setting is correct for your source. Verify all connections and speaker leads. If the standby indicator is flashing, the amplifier protection circuitry may have been activated, and you should contact your Integra/Onkyo authorized Service Center.
Y
Yvonne RayAug 22, 2025
Why is there no sound or very minimal sound from the center speaker on my Integra Receiver?
- S
  Samantha MooreAug 22, 2025
  First, check the connection between the amplifier and the speaker. Ensure that the listening mode is not set to ORCHESTRA or STEREO; if it is, switch to another mode. Also, verify that the CENTER level is not set to minimum and that the CENTER SPEAKER setting is not set to NONE; if it is, set it to LARGE or SMALL.
M
Matthew EvansAug 25, 2025
Why is the sound of the playback source not heard on my Integra Receiver?
- P
  pzimmermanAug 25, 2025
  Ensure that the input selector is properly set to the playback source.
P
Philip AndersonAug 26, 2025
What to do if my Integra DTR-5.1 has no power?
- T
  Travis SmithAug 26, 2025
  First, ensure the power cord is properly connected. If it is, try turning the power off and on again, or unplug the AC cord from the outlet, wait a few seconds, and plug it back in. If the issue persists, it might be due to a blown AC fuse, in which case you should contact your Integra/Onkyo authorized Service Center.
T
Tonya HendersonAug 28, 2025
What to do if the front panel controls on my Integra Receiver work, but the remote controller doesn't?
- B
  brittanythompsonAug 28, 2025
  First, check if there are batteries in the remote controller and insert them if missing. If batteries are present, try replacing them, as they may be worn out.
J
jason63Aug 29, 2025
Why is there hum or low-frequency noise coming from my Integra DTR-5.1 Receiver?
- J
  Justin ReedAug 29, 2025
  This could be due to a poor or missing input ground, so check the outer conductor of the input plugs. Also, inspect the phono motor ground for a proper connection. Adjust the placement of the audio connection cables on the rear panel to potentially reduce the hum.
K
Kevin WallaceAug 31, 2025
What to do if I can't receive AM stations on my Integra DTR-5.1 Receiver?
- A
  andreaguerreroAug 31, 2025
  Ensure that the included AM loop antenna is connected to the AM antenna terminals.
C
Christopher JonesSep 2, 2025
What to do if I press the on button on the remote controller, but the Integra DTR-5.1 Receiver doesn't turn on?
- A
  Angela FoxSep 2, 2025
  Make sure to press the MODE AUDIO button first, and then press the ON button.
J
jacob46Sep 4, 2025
What to do if my Integra DTR-5.1 Receiver or connected device doesn't respond to operation?
- T
  tarascottSep 4, 2025
  Be sure to press an appropriate MODE button before pressing the operation button.
R
Rebecca MunozSep 5, 2025
Why is my Integra DTR-5.1 making a buzzing noise on AM?
- B
  Brenda PatelSep 5, 2025
  The buzzing noise may be caused by electrical apparatus like a fluorescent lamp. Try moving the AM loop antenna to a different position. Alternatively, set up an outdoor AM antenna.

Integra DTR-5.1 Specifications

General

Channels	5.1
Total Harmonic Distortion (THD)	0.08%
Input Impedance	47 kOhms
Audio Formats Supported	Dolby Digital, DTS, Dolby Pro Logic II
Video Formats Supported	Composite, S-Video
Input Sensitivity	200 mV
Signal-to-Noise Ratio	100 dB
Digital Inputs	2 Optical, 1 Coaxial
Frequency Response	10Hz - 100kHz
Speaker Impedance	8 ohms
Audio Inputs	5 Analog