To Next Page
J
jacob46Sep 4, 2025
What to do if my Integra DTR-5.1 Receiver or connected device doesn't respond to operation?
- TtarascottSep 4, 2025
Be sure to press an appropriate MODE button before pressing the operation button.
What to do if my Integra DTR-5.1 Receiver or connected device doesn't respond to operation?
Be sure to press an appropriate MODE button before pressing the operation button.
Why is no station recalled on my Integra Receiver?
This may occur if the power cord has been unplugged or the Power switch has been turned off for an extended period. Try storing all stations again.
Why do the TUNED and STEREO indicators flicker, and hiss is heard on FM with my Integra DTR-5.1 Receiver?
The station signal is likely too weak. Try installing an outdoor FM antenna. Stereo FM broadcasts cover only about half the distance of an ordinary broadcast, so changing the position or direction of the outdoor antenna may also help.
Why do the TUNED and STEREO indicators light up, but the sound is distorted, and the stereo separation is bad on my Integra DTR-5.1?
The station signal may be too strong. Try changing to an FM indoor antenna. Alternatively, multiple reflections of radio waves from tall buildings or mountains could be the issue. Use an antenna with better directivity and select a point where the distortion is minimal.
Why does my Integra DTR-5.1 Receiver sound rough or scratchy, and the high range isn't clear?
This could be because the stylus of your turntable pick-up is worn, in which case you should replace it. Alternatively, the turntable stylus tip may be dirty, so try cleaning it. Also, check if the treble control is set too high and turn it down if necessary.
Why is my Integra DTR-5.1 Receiver howling when the volume is turned up?
The turntable and speakers may be too close together. Try moving them farther apart.
Why is my Integra DTR-5.1 making a crackling noise on AM and FM?
This could be due to noise from a fluorescent lamp being turned on and off, so move the antenna as far as possible from the lamp. It could also be noise from automobile ignition, so install an FM outdoor antenna as far as possible from the road. You can also try changing the position or direction of the outdoor antenna.
Why is there a high-pitched or buzzing noise on AM with my Integra Receiver?
This noise could be coming from a TV set. Try placing the AM loop antenna as far away from the TV as possible, or move the unit away from the TV set.
Why is my Integra DTR-5.1 making a buzzing noise on AM?
The buzzing noise may be caused by electrical apparatus like a fluorescent lamp. Try moving the AM loop antenna to a different position. Alternatively, set up an outdoor AM antenna.
Why is there power on my Integra DTR-5.1 Receiver but no sound?
There could be several reasons for this. Check if the MUTING indicator is lit and, if so, press the MUTING button on the remote to turn it off. Also, ensure the digital/analog input setting is correct for your source. Verify all connections and speaker leads. If the standby indicator is flashing, the amplifier protection circuitry may have been activated, and you should contact your Integra/Onkyo authorized Service Center.
Covers fire, electric shock, moisture, ventilation, heat, and power safety measures.
Instructions for use, cleaning, servicing, and general appliance care.
Setting parameters for subwoofer, front, center, and surround speakers.
Adjusting speaker distances and finalising sizes for center/surround.
Guide to calibrating speaker levels using the test tone feature.
Setting speaker levels for Multi CH Input and configuring power-on volume.
Details on specific mode parameters like Late Night, Front Effect, Re-EQ, and LFE.
Step-by-step instructions for saving radio frequencies to memory.
Step-by-step guide to teaching the remote new commands.
Procedures for removing learned codes from individual buttons and modes.
Explains macros and provides steps for setting them up.
Procedure for erasing all programmed codes and macros.
Guide to creating single-button sequences for direct device control.
How to remove programmed sequences from MACRO MODE and DIRECT.
Solutions for common problems with the remote, audio, noise, and signal reception.
Identification and explanation of the receiver's front panel elements.
General| Channels | 5.1 |
|---|---|
| Total Harmonic Distortion (THD) | 0.08% |
| Input Impedance | 47 kOhms |
| Audio Formats Supported | Dolby Digital, DTS, Dolby Pro Logic II |
| Video Formats Supported | Composite, S-Video |
| Input Sensitivity | 200 mV |
| Signal-to-Noise Ratio | 100 dB |
| Digital Inputs | 2 Optical, 1 Coaxial |
| Frequency Response | 10Hz - 100kHz |
| Speaker Impedance | 8 ohms |
| Audio Inputs | 5 Analog |
