Need help?Do you have a question about the Integra DTR-10.5 and is the answer not in the manual?
Amplifier Specifications| amplifier power output at 6 ohms | 200 W per channel |
|---|---|
| amplifier power output at 8 ohms | 150 W per channel |
| dynamic power output at 3 ohms | 2 x 340 W |
| dynamic power output at 4 ohms | 2 x 260 W |
| dynamic power output at 8 ohms | 2 x 175 W |
| frequency response | 5 Hz to 100 kHz |
| signal-to-noise ratio | 110 dB |
| total harmonic distortion | 0.08% |
| damping factor | 60 at 8 ohms |
Input and Output Specifications| line input sensitivity and impedance | 200 mV, 50 k ohms |
|---|---|
| multi-channel input sensitivity and impedance | 200 mV, 50 k ohms |
| subwoofer input sensitivity and impedance | 36 mV, 50 k ohms |
| rec out level and impedance | 200 mV, 470 ohms |
| pre out level and impedance | 1 V, 470 ohms |
| zone 2/3 line output level and impedance | 100 mV, 470 ohms |
Radio Specifications| AM tuning range | 530–1, 710 kHz |
|---|---|
| AM usable sensitivity | 30 µV |
| FM tuning range | 87.5–108.0 MHz |
| FM usable sensitivity, stereo | 17.2 dBf, 2.0 µV (75 ohms IHF) |
Phono and Tone Control| phono input sensitivity | 2.5 mV, 50 k ohms |
|---|---|
| phono overload | 70 mV RMS at 1 kHz, 0.5% THD |
| RIAA deviation | 20 Hz to 20 kHz: ±0.8 dB |
| phono signal-to-noise ratio | 80 dB |
| bass control | ±12 dB at 50 Hz |
| mid range control | ±12 dB at 1, 000 Hz |
| treble control | ±12 dB at 20, 000 Hz |
General Specifications| power supply | AC 120 V, 60 Hz |
|---|---|
| power consumption | 13.0 A |
| dimensions | 435 x 175 x 429 mm |
| weight | 32.1 kg |
Instructions on how to safely connect the power cord to the unit and AC inlet.
Guidance on operating the remote controller, including sensor alignment and environment.
Guidance on basic speaker setup for home theater and the role of each speaker.
Instructions on stripping wire, twisting ends, and connecting speaker cables.
Instructions for connecting a subwoofer using PRE OUT jacks or an external amplifier.
Guide for connecting an external amplifier to the PRE OUT terminals for louder listening.
Guide for connecting TVs or projectors to display video sources or operating information.
Instructions for connecting a DVD player using digital and analog terminals.
Procedure for connecting a DVD recorder or digital VCR to the VIDEO 1 input.
Guide for connecting a VCR to the VIDEO 2 or VIDEO 3 inputs.
Instructions for connecting DBS tuners, DBS TV, or BS/CS tuners.
Instructions for connecting devices via the i.LINK (AUDIO) terminal.
Guide for connecting HDMI-enabled devices for high-definition multimedia interface.
Instructions for connecting devices to the 12V TRIGGER OUT terminals.
Explanation of basic remote controller operations in AMP mode.
Instructions for connecting the power cord and turning the unit on/off.
Steps to select listening modes using input source buttons and remote.
Instructions for connecting devices for multichannel playback.
Steps to configure input source type and settings for multichannel playback.
Guide for enjoying a different source in Zone 2 with only speakers connected.
How to connect a pre-main amplifier or receiver for Zone 2 or Zone 3.
Instructions for connecting a power amplifier for Zone 2 or Zone 3.
Steps to record audio/video while playing another source.
How to record audio/video on one component while playing another.
Guide to recording custom video by combining audio and video from different sources.
Diagram and instructions for connecting the DTR-10.5 to an Ethernet network.
Steps to listen to Internet radio stations by genre, location, or language.
Instructions for playing music files saved on a network audio server.
Steps to configure music server settings for network audio playback.
Instructions on how to navigate and use the Setup Menu.
Settings for remote control ID to prevent interference.
Configuring speaker assignments for Main A, Main B, and Zone 2.
Setting speaker impedance to match connected speakers.
Setting crossover frequencies for bass sounds to the subwoofer.
Adjusting speaker volume levels for balanced sound.
Configuring THX Ultra2 settings for optimal audio performance.
Allocating audio output jacks to input sources for playback.
Allocating video output jacks to input sources for playback.
Configuring audio input assignments for various sources.
Configuring video input assignments for various sources.
Specifying preferred listening modes for each input source.
Assigning rooms or devices to 12V trigger outputs.
Configuring audio effect and playback for Mono listening mode.
Configuring audio effect and playback for Multiplex listening mode.
Configuring audio effect and playback for Stereo listening mode.
Configuring audio effect and playback for Direct/Pure Audio modes.
Configuring audio effect and playback for analog multichannel sources.
Configuring playback options for DVD-Audio via i.LINK.
Configuring playback options for Super Audio CD via i.LINK.
Configuring audio effect and playback for Dolby Digital sources.
Configuring audio effect and playback for DTS sources.
Configuring audio effect and playback for AAC sources.
Configuring playback options for 2ch sources with PLIIx/NEO:6 modes.
Configuring audio effect and playback options for THX modes.
Configuring audio effects for Integra original listening modes.
Configuring audio effects for All Ch Stereo and Full Mono modes.
Configuring playback options for Dolby Virtual Speaker effect.
Troubleshooting steps for power-related issues like unit not turning on.
Solutions for no sound, quiet sound, or incorrect speaker output.
Technical specifications for the amplifier section.
To Next Page
