To Next PageTo Next PageWhat to do if Integra DTR-7.1 Receiver does not recall preset station?
If your Integra Receiver does not recall a preset station, the memory contents are lost. Store all stations again, because the power cord has been unplugged or the POWER switch has been turned off for a long time.
Why is there no sound from Integra Receiver center speaker?
If there is no sound or very low volume from the center speaker of your Integra Receiver, check the connection between the amplifier and the speaker. Ensure the Listening mode is set to a mode other than Stereo or Direct. Verify the CENTER level is set to an appropriate volume. Confirm that CENTER SPEAKER is set to “Large” or “Small,” not “None.”
Why is there no sound from Integra Receiver surround back speakers?
If there is no sound from the surround back speakers on your Integra Receiver, check the Surr Back Out setting. If one surround back speaker is connected, select “1 ch,” and if two surround back speakers are connected, select “2 ch”. If the Dolby D 6.1/DTS-ES setting is “Off,” there is no output to the surround back speakers. Change the setting to “Auto” or “On.” If the Dolby D THX Surround EX/DTS THX Surround EX setting is “Off,” there is no output to the surround back speakers. Change the setting to “Auto” or “On.”
Why is there no sound or very low volume from Integra DTR-7.1 subwoofer?
If there is no sound or very low volume from the subwoofer of your Integra Receiver, check the speaker setting. Check the output level of the Subwoofer using the test tone.
What to do if Integra Receiver power turns on but no sound?
If your Integra Receiver powers on but produces no sound, first, check if “Muting” is displayed and, if so, press the MUTING button on the remote controller to turn it off. Then, check all connections and speaker cables to ensure they are properly connected. If the amplifier protection circuitry has been activated, contact your Integra/Onkyo authorized Service Center.
How to fix howling sound when Integra Receiver volume is turned up?
If howling is heard when the volume is turned up on your Integra Receiver, move the turntable and speakers farther apart because they are located too close together.
Why is Integra DTR-7.1 sound distorted and stereo separation bad?
If the indicators light for stereo reception, but the sound is distorted and stereo separation is bad on your Integra Receiver, change to an FM indoor antenna, because the station is too strong. If the issue persists, use an antenna that has better directivity and select a point where distortion is least, because of multiple reflection of the radio waves because of tall buildings or mountains.
Why do Integra Receiver stereo reception flicker and hiss on FM stations?
If the indicators for stereo reception flicker and hiss is heard on FM stations with your Integra Receiver, install an outdoor FM antenna, because the station is too weak. Also, change the position or direction of the outdoor antenna, because stereo FM broadcasts cover only about half the distance of an ordinary broadcast.
What to do if Integra DTR-7.1 Receiver picture and sound do not match?
If the picture and sound do not match on your Integra Receiver, check the connections. Also, check settings in the Video Setup sub-menu of the Input Setup menu.
What to do if Integra DTR-7.1 Receiver remote controller doesn't work?
If the front panel controls on your Integra Receiver work, but the remote controller does not, first insert batteries or replace them if they are worn out. Ensure that the remote controller is pointed at the remote sensor of the DTR-7.1. Finally, check that the remote controller is functioning in the correct mode by pressing the AUDIO MODE button.
General| Audio Channels | 7.1 |
|---|---|
| Total Harmonic Distortion (THD) | 0.08% |
| THX Certified | Yes |
| HDMI Outputs | 1 |
| Component Video Inputs | 2 |
| Component Video Outputs | 1 |
| Analog Audio Inputs | 6 |
| Headphone Jack | Yes |
| Tuner | AM/FM |
| Remote Control | Yes |
| Input Sensitivity | 200 mV |
| Signal-to-Noise Ratio | 100 dB |
| Input Connections | HDMI, Component, Digital Coaxial, Digital Optical, Analog Audio |
| Output Connections | HDMI, Component, Composite, Analog Audio, Subwoofer Pre-out |
| Digital Audio Inputs | 2 Optical, 2 Coaxial |
| Digital Audio Outputs | 1 Optical |
Details the process for inserting batteries into the remote controller.
Guidelines for operating the remote controller and sensor.
General guidelines for connecting main audio and video components.
Details on connecting turntables, CD players, and tape decks.
Details on connecting DVD players, VCRs, and other video sources.
Instructions for connecting TV and satellite tuners via analog and digital interfaces.
How to connect DVD recorders and digital video devices.
Guide for connecting monitors and projectors to output terminals.
How to connect video cameras and game consoles to front panel inputs.
Recommended placement and types for ideal speaker setup.
Basic speaker requirements for surround sound.
General advice on speaker positioning based on room size.
Key considerations for placing front and surround speakers correctly.
Step-by-step instructions for preparing and connecting speaker cables.
How to connect a subwoofer using the PRE OUT jack.
Instructions for assembling the AM loop antenna.
Steps to connect the AM antenna cable to the unit.
How to connect and position the FM indoor antenna for best reception.
Considerations for installing an FM outdoor antenna.
Recommendations for installing an AM outdoor antenna.
Advice on using splitters for common FM/TV antennas.
How to connect speakers for Zone 2 operation.
Connecting the DTR-7.1 to an amplifier for remote zone output.
How to connect external power amplifiers for increased volume.
Connecting surround back speakers via amplifier and OSD settings.
Physical connection of the power cord to the unit and wall outlet.
Steps to turn the unit on and off using the remote control.
Main menu for configuring speaker parameters such as size, distance, and level calibration.
Main menu for setting up audio and video input sources and their formats.
Main menu for selecting and customizing various audio listening modes.
Menu for adjusting volume display, maximum volume, and power-on volume settings.
Menu for customizing OSD display settings like color and position.
How to navigate and use the OSD menu with the remote or front panel controls.
Main menu for speaker configuration, including size, distance, and levels.
Sub-menu for defining speaker size (Large/Small) and subwoofer presence.
Sub-menu for setting speaker distances from the listening position.
Sub-menu for adjusting individual speaker volume levels using test tones.
Sub-menu for limiting bass output to protect the subwoofer or front speakers.
Main menu for setting up various input sources, including audio, video, and digital formats.
Sub-menu for configuring digital input connections and formats for each source.
Setting for assigning digital input jacks (OPT1, OPT2, COAX1, COAX2) to input sources.
Setting for automatic or specific signal format detection (All, DTS, PCM).
Setting to enable multichannel audio input via the MULTI CHANNEL INPUT port.
Sub-menu for matching audio sources with video sources or setting component video inputs.
Sub-menu for assigning specific listening modes to different input signal types.
Detailed descriptions of various listening modes like Stereo, Direct, Surround, THX, etc.
Setting for Dolby Digital sources with THX Surround EX.
Setting for DTS sources with THX Surround EX.
Adjusts reverberation effects for live recordings.
Adjusts the strength of sound effects.
Simulates hall size for surround modes.
Mode for a multi-speaker setup, optimizing sound reproduction.
Mode for 7-channel speakers, reproducing natural surround.
Mode for classical music, simulating hall acoustics.
Mode for TV programs, enhancing clarity and surround.
Mode for acoustic music, simulating stage acoustics.
Mode for popular music, simulating club acoustics.
Mode for background music, creating an encompassing stereo image.
Sub-menu for adjusting bass and treble levels for input sources.
Sub-menu for setting automatic volume adjustment for different input sources.
Sub-menu for controlling external devices via 12V TRIGGER terminals based on input source.
Main menu for adjusting parameters of various listening modes.
Settings for the Stereo listening mode, including subwoofer and Re-EQ.
Settings for Theater-Dimensional mode, including listening angle and dialog enhance.
Settings for Dolby Digital, DTS, and Pro Logic surround modes.
Settings for THX listening modes, including Re-EQ and surround speakers.
Settings for Mono Movie mode, including front effect and room size.
Settings for Enhanced 7 mode, adjusting front effect and room size.
Settings for Orchestra, Unplugged, Studio-Mix, and TV Logic modes.
Settings for All Ch Stereo mode, adjusting subwoofer and Re-EQ.
Detailed explanations of listening mode parameters like Subwoofer, Re-EQ, Surround Speakers, etc.
How to set the listening angle for optimal sound reproduction.
Options for center channel output (Center speaker or Phantom Center).
Function to spread front speaker sound for a wider space.
Adjusts the virtual surround sound level.
Enhances dialog clarity from the center speaker.
Main menu for adjusting volume settings, headphone level, and Zone 2.
Sub-menu for volume display, maximum volume, and power-on volume settings.
Adjusts headphone volume output to match speaker levels.
Sets the LFE level for DTS sources.
Settings for Zone 2 operation, including speaker connection or amplifier connection.
Main menu for customizing on-screen display settings like color and position.
Sub-menu for setting OSD output to S-Video or Video terminals.
Sub-menu for customizing OSD background color, superimpose mode, and immediate display.
Sub-menu for adjusting the OSD menu's position on the screen.
How to control the unit from a remote location using the remote controller.
How to control Zone 2 functions using the unit's front panel buttons.
How to access and enjoy FM and AM radio stations on the DTR-7.1.
Step-by-step guide for manually tuning into radio stations.
How to store favorite radio stations for quick access.
How to recall stored radio stations using the remote or front panel.
How to remove stored radio stations.
How to choose the active input source for audio and video playback.
How to control the main volume output for speakers and headphones.
How to select different audio modes for playback.
How to connect and use headphones with the unit.
Overview of additional features like changing speaker levels, sleep timer, bass/treble, and display brightness.
Explains error messages that may appear during operation.
Guide to setting up and playing multichannel audio sources.
How to output the currently selected source for recording.
How to record a different source than the one being monitored.
How to mix audio from one source with video from another for recording.
How to assign custom names to input sources for easier identification.
Procedure to delete custom names assigned to input sources.
How to assign custom names to preset radio stations.
How to modify existing custom names for input sources or stations.
Introduction to the remote controller's functions and operation.
General steps for operating connected components with the remote.
How to operate the main unit using the remote controller.
How to control an Integra/Onkyo CD player using the remote.
How to control an Integra/Onkyo MD recorder using the remote.
How to control an Integra/Onkyo cassette tape deck using the remote.
How to select preset radio stations using the remote.
How to control an Integra DVD player using the remote controller.
How to program the remote for TV, VCR, Cable, and Satellite devices.
Step-by-step guide for learning commands from other remote controllers.
How to erase a single programmed command from a remote button.
How to erase all commands assigned to a specific MODE button.
Explanation of what a macro function is and its purpose.
Step-by-step guide for programming a sequence of operations into a macro.
How to program a macro into the dedicated DIRECT MACRO button.
How to execute a programmed direct macro function.
How to erase a macro from a MODE MACRO button.
How to erase a macro from the DIRECT MACRO button.
Procedure to reset the remote controller to factory defaults by erasing all programmed data.
Solutions for issues related to power on/off and protection circuits.
Troubleshooting sound issues related to speakers, especially center and surround back speakers.
Causes and solutions for humming noise issues.
Troubleshooting causes of howling sounds at high volumes.
Solutions for sound clarity and scratchy audio problems.
Reasons for lack of sound from surround back speakers and how to fix them.
Solutions for AM/FM reception issues, noise, and weak signals.
Troubleshooting for video display, OSD, picture/sound sync, and no sound issues.
Solutions for remote controller not functioning, dead batteries, or incorrect mode.
Issues with remote zone components and interference.
