Integra DTR-10.5 User Manual

51
Operations
Basic Operation of Remote Controller Buttons —Continued
Before operating the connected component, follow the
instructions on pages 124 through 133 to make
appropriate settings using the remote controller.
When you perform the procedures on the DTR-10.5,
press the [Zone 2] (or [Rec/Zone 3]), and turn the
[Select/Preset] (or [Control/Tuning]).
Before performing the following procedure, complete
your macro settings (See page 137).
Use the [Custom] button “to enter the remote controller code for another apparatus to this remote controller,” “to make
this remote controller learn specified operations from the remote controller for another apparatus,” or “to make this
remote controller learn a series of operations with macro functions” according to the configuration you are using. For
detailed information, see pages 136-142.
To Operate a Connected Component (Mode Switching)
ABC DEF
PQRS TUV WXYZ
GHI JKL MNO
@.-'/
--
/
---
Direct Tuning
#
Custom
Dimmer
T V
Input
Sleep
On Standby
T
V
T
V CH
T
V VOL
+
10 0
Clear
123
456
789
Input
T
o
p
M
e
n
u
M
e
n
u
H
I
+
-
+
Zone 3
Zone
2
InputMode
Macro
S
e
r
v
e
r
A
u
d
i
o
A
D
J
Mode
Scroll wheel
1
Press the [Mode] button.
The [Mode] button lights.
2
Roll the scroll wheel.
Indication on the lower line
changes to indicate the
selected component mode.
To Select a Source in Zone 2 or Zone 3
ABC DEF
PQRS TUV WXYZ
GHI JKL MNO
@.-'/
--
/
---
Direct Tuning
#
Custom
Dimmer
T V
Input
Sleep
On Standby
T
V
T
V CH
T
V VOL
E
x
i
t
G
u
i
d
e
Prev
Enter
R
+
10 0
Clear
123
456
789
Input
T
o
p
M
e
n
u
M
e
n
u
VOL
CH
Disc
I
+
-
+
-
Zone 3
Zone
2
InputMode
Macro
S
e
r
v
e
r
A
u
d
i
o
A
D
J
Zone 3
Zone 2
Scroll wheel
1
Press the [Zone 2] or [Zone 3] button.
The [Zone 2] or [Zone 3] button lights.
2
Roll the scroll wheel.
Indication on the upper
line changes to indicate
the selected input.
To Perform a Macro Operation
ABC DEF
PQRS TUV WXYZ
GHI JKL MNO
@.-'/
--
/
---
Direct Tuning
#
Custom
Dimmer
T V
Input
Sleep
On Standby
T
V
T
V CH
T
V VOL
+
10 0
Clear
123
456
789
Input
T
o
p
M
e
n
u
M
e
n
u
I
+
-
Zone 3
Zone
2
InputMode
Macro
e
r
v
e
r
A
u
d
i
o
Macro
Scroll wheel
1
Press the [Macro] button.
The [Macro] button lights.
2
Roll the scroll wheel to select the macro’s
number, and then press the scroll wheel.
Customizing Your Remote Controller

Integra DTR-10.5 Specifications

Amplifier Specifications

amplifier power output at 6 ohms	200 W per channel
amplifier power output at 8 ohms	150 W per channel
dynamic power output at 3 ohms	2 x 340 W
dynamic power output at 4 ohms	2 x 260 W
dynamic power output at 8 ohms	2 x 175 W
frequency response	5 Hz to 100 kHz
signal-to-noise ratio	110 dB
total harmonic distortion	0.08%
damping factor	60 at 8 ohms

Input and Output Specifications

line input sensitivity and impedance	200 mV, 50 k ohms
multi-channel input sensitivity and impedance	200 mV, 50 k ohms
subwoofer input sensitivity and impedance	36 mV, 50 k ohms
rec out level and impedance	200 mV, 470 ohms
pre out level and impedance	1 V, 470 ohms
zone 2/3 line output level and impedance	100 mV, 470 ohms

Radio Specifications

AM tuning range	530–1, 710 kHz
AM usable sensitivity	30 µV
FM tuning range	87.5–108.0 MHz
FM usable sensitivity, stereo	17.2 dBf, 2.0 µV (75 ohms IHF)

Phono and Tone Control

phono input sensitivity	2.5 mV, 50 k ohms
phono overload	70 mV RMS at 1 kHz, 0.5% THD
RIAA deviation	20 Hz to 20 kHz: ±0.8 dB
phono signal-to-noise ratio	80 dB
bass control	±12 dB at 50 Hz
mid range control	±12 dB at 1, 000 Hz
treble control	±12 dB at 20, 000 Hz

General Specifications

power supply	AC 120 V, 60 Hz
power consumption	13.0 A
dimensions	435 x 175 x 429 mm
weight	32.1 kg