EasyManuals Logo

Integra DTR-10.5 User Manual

Integra DTR-10.5
152 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #118 background imageLoading...
Page #118 background image
118
Audio Adjust
You can adjust bass, mid, and treble notes for each
speaker set.
For any speaker set to “Not Used” in the Speaker
Configuration sub-menu, no associated setting item is
displayed.
Front Bass
Option for adjusting bass notes from front L/R
speakers. Specify at 1 dB intervals in a range from
–12 dB to +12 dB. The default is “0.
This option can also be set for Zone 2.
Front Mid
Option for adjusting mid notes from front L/R speakers.
Specify at 1 dB intervals in a range from –12 dB to
+12 dB. The default is “0.
This option can also be set for Zone 2.
Front Treble
Option for adjusting treble notes from front L/R
speakers. Specify at 1 dB intervals in a range from
–12 dB to +12 dB. The default is “0.
This option can also be set for Zone 2.
Center Bass
Option for adjusting bass notes from the center speaker.
Specify at 1 dB intervals in a range from –12 dB to
+12 dB. The default is “0.
Center Mid
Option for adjusting mid notes from the center speaker.
Specify at 1 dB intervals in a range from –12 dB to
+12 dB. The default is “0.
Center Treble
Option for adjusting treble notes from the center
speaker. Specify at 1 dB intervals in a range from
–12 dB to +12 dB. The default is “0.
Surr L/R Bass
Option for adjusting bass notes from surround L/R
speakers. Specify at 1 dB intervals in a range from
–12 dB to +12 dB. The default is “0.
Surr L/R Mid
Option for adjusting mid notes from surround L/R
speakers. Specify at 1 dB intervals in a range from
–12 dB to +12 dB. The default is “0.
Surr L/R Treble
Option for adjusting treble notes from surround L/R
speakers. Specify at 1 dB intervals in a range from
–12 dB to +12 dB. The default is “0.
Surr Bk Bass
Option for adjusting bass notes from the surround back
speaker. Specify at 1 dB intervals in a range from –12
dB to +12 dB. The default is “0.
If “Surr Back” is set to “BTL for Front” or “Bi-Amp
for Front” on the Speaker Configuration sub-menu,
this item is not displayed.
Surr Bk Mid
Option for adjusting mid notes from the surround back
speaker. Specify at 1 dB intervals in a range from –12
dB to +12 dB. The default is “0.
If “Surr Back” is set to “BTL for Front” and “Bi-Amp
for Front” on the Speaker Configuration sub-menu,
this item is not displayed.
Surr Bk Treble
Option for adjusting treble notes from the surround
back speaker. Specify at 1 dB intervals in a range from
–12 dB to +12 dB. The default is “0.
If “Surr Back” is set to “BTL for Front” or “Bi-Amp
for Front” on the Speaker Configuration sub-menu,
this item is not displayed.
Subwoofer Bass
Option for adjusting bass notes from the subwoofer.
Specify at 1 dB intervals in a range from –12 dB to
+12 dB. The default is “0.
Tone Control Sub-menu

Table of Contents

Other manuals for Integra DTR-10.5

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Integra DTR-10.5 and is the answer not in the manual?

Integra DTR-10.5 Specifications

Amplifier Specifications IconAmplifier Specifications
amplifier power output at 6 ohms200 W per channel
amplifier power output at 8 ohms150 W per channel
dynamic power output at 3 ohms2 x 340 W
dynamic power output at 4 ohms2 x 260 W
dynamic power output at 8 ohms2 x 175 W
frequency response5 Hz to 100 kHz
signal-to-noise ratio110 dB
total harmonic distortion0.08%
damping factor60 at 8 ohms
Input and Output Specifications IconInput and Output Specifications
line input sensitivity and impedance200 mV, 50 k ohms
multi-channel input sensitivity and impedance200 mV, 50 k ohms
subwoofer input sensitivity and impedance36 mV, 50 k ohms
rec out level and impedance200 mV, 470 ohms
pre out level and impedance1 V, 470 ohms
zone 2/3 line output level and impedance100 mV, 470 ohms
Radio Specifications IconRadio Specifications
AM tuning range530–1, 710 kHz
AM usable sensitivity30 µV
FM tuning range87.5–108.0 MHz
FM usable sensitivity, stereo17.2 dBf, 2.0 µV (75 ohms IHF)
Phono and Tone Control IconPhono and Tone Control
phono input sensitivity2.5 mV, 50 k ohms
phono overload70 mV RMS at 1 kHz, 0.5% THD
RIAA deviation20 Hz to 20 kHz: ±0.8 dB
phono signal-to-noise ratio80 dB
bass control±12 dB at 50 Hz
mid range control±12 dB at 1, 000 Hz
treble control±12 dB at 20, 000 Hz
General Specifications IconGeneral Specifications
power supplyAC 120 V, 60 Hz
power consumption13.0 A
dimensions435 x 175 x 429 mm
weight32.1 kg

Related product manuals