EasyManuals Logo

Integra DTR-10.5 User Manual

Integra DTR-10.5
152 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #72 background imageLoading...
Page #72 background image
72
Enjoying Net Audio
You can enjoy Net Audio when the ETHER-
NET terminal board [B] (for Net Audio) is
inserted.
The DTR-10.5 can be used as a Net-Tune client on a
standard Ethernet network, allowing you to play music
(MP3, WAV) stored on your Network Audio server
through the DTR-10.5. If your network is connected to
the Internet, you can also tune into Internet radio sta-
tions.
Internet Radio
With Internet radio you can:
Listen to stations that use MP3 format streaming.
Select stations by genre, location, or language.
Preset up to 30 Internet radio stations.
Net-Tune
For audio delivery over Ethernet, Integra developed
NTSP (Net-Tune System Protocol). Since it’s based on
the industry standard TCP/IP protocol, it’s efficient and
very responsive.
The Network Audio server supports the MP3 and WAV
formats.
AWAV:
high-quality, uncompressed, linear PCM.
MP3:
high-quality, compressed, small file size.
For more information about Net-Tune, see the following
Integra Web sites.
http://www.integrahometheater.com/
Network Requirements
Ethernet Network
The DTR-10.5’s Ethernet port supports 10Base-T. For
best results, a 100Base-T switched Ethernet network is
recommended. Although it’s theoretically possible to
use a wireless network, due to unpredictable perfor-
mance, it may not provide satisfactory results, so a
wired network is recommended.
Ethernet Router
A router manages the network, routing data and supply-
ing IP addresses. Your router must support the follow-
ing:
NAT NAT (Network Address Translation). NAT
allows several networked computers to access the
Internet simultaneously via a single Internet connec-
tion. The DTR-10.5 needs Internet access for Internet
radio.
DHCP (Dynamic Host Configuration Protocol).
DHCP supplies IP address information to network
devices, allowing them to configure themselves auto-
matically.
A router with a 100Base-TX switch built-in is recom-
mended.
Some routers have a modem built-in, and some ISPs
require you to use specific routers. Please consult your
ISP or computer dealer if you’re unsure.
CAT5 Ethernet cable
Use a standard CAT5 Ethernet cable (straight-type).
Internet Access (for Internet radio)
To use Internet radio, your Ethernet network must have
Internet access. A narrowband Internet connection (e.g.,
56K modem, ISDN) will not provide satisfactory
results, so a broadband connection is strongly recom-
mended (e.g., cable modem, xDSL modem, etc). Please
consult your ISP or computer dealer if you’re unsure.
About Net-Tune

Table of Contents

Other manuals for Integra DTR-10.5

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Integra DTR-10.5 and is the answer not in the manual?

Integra DTR-10.5 Specifications

Amplifier Specifications IconAmplifier Specifications
amplifier power output at 6 ohms200 W per channel
amplifier power output at 8 ohms150 W per channel
dynamic power output at 3 ohms2 x 340 W
dynamic power output at 4 ohms2 x 260 W
dynamic power output at 8 ohms2 x 175 W
frequency response5 Hz to 100 kHz
signal-to-noise ratio110 dB
total harmonic distortion0.08%
damping factor60 at 8 ohms
Input and Output Specifications IconInput and Output Specifications
line input sensitivity and impedance200 mV, 50 k ohms
multi-channel input sensitivity and impedance200 mV, 50 k ohms
subwoofer input sensitivity and impedance36 mV, 50 k ohms
rec out level and impedance200 mV, 470 ohms
pre out level and impedance1 V, 470 ohms
zone 2/3 line output level and impedance100 mV, 470 ohms
Radio Specifications IconRadio Specifications
AM tuning range530–1, 710 kHz
AM usable sensitivity30 µV
FM tuning range87.5–108.0 MHz
FM usable sensitivity, stereo17.2 dBf, 2.0 µV (75 ohms IHF)
Phono and Tone Control IconPhono and Tone Control
phono input sensitivity2.5 mV, 50 k ohms
phono overload70 mV RMS at 1 kHz, 0.5% THD
RIAA deviation20 Hz to 20 kHz: ±0.8 dB
phono signal-to-noise ratio80 dB
bass control±12 dB at 50 Hz
mid range control±12 dB at 1, 000 Hz
treble control±12 dB at 20, 000 Hz
General Specifications IconGeneral Specifications
power supplyAC 120 V, 60 Hz
power consumption13.0 A
dimensions435 x 175 x 429 mm
weight32.1 kg

Related product manuals