EasyManuals Logo

Integra DTR-10.5 User Manual

Integra DTR-10.5
152 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #73 background imageLoading...
Page #73 background image
73
Operations
Enjoying Net Audio
—Continued
Notes:
To use Internet radio with the DTR-10.5, your broad-
band Internet connection needs to be up and running
and able to access the Web. Please consult your ISP if
you have any problems with your Internet connec-
tion.
The DTR-10.5 uses DHCP and AutoIP to configure
its network settings automatically. If you want to con-
figure these settings manually, see page 121.
The DTR-10.5 does not support PPPoE settings, so if
you have a PPPoE-type Internet connection, you must
use a PPPoE-compatible router.
Depending on your ISP, you may need to specify a
proxy server to use Internet radio. If your PC is con-
figured to use a proxy server, use the same settings
(see page 121).
To connect the DTR-10.5 to your Ethernet network, plug one end of a CAT5 Ethernet cable into the ETHERNET (Net-
Tune) port, and plug the other end into a LAN port on your router or switch.
The following diagram shows how you can connect the DTR-10.5 to your Ethernet network. Here it’s connected to a
LAN port on the router, which has a 4-port 100Base-TX switch built-in.
You can connect any number of DTR-10.5s to the network, and the Network Audio server can serve up to three clients
simultaneously, so you can enjoy Net-Tune in three separate rooms simultaneously. The following diagram shows a Net-
Tune network with two DTR-10.5s.
Networking Your DTR-10.5
E
GND
“Net
-
Tune”
is
a
trademark
of
Onkyo
Corporation.
ETHERNET
(
Net
-
Tune
)
A
RS
232
IR
IN
+
12
V DC PWR SUPPLY
MAIN
GND
ZONE
3
ZONE
2
20mA MAX.
12 V
TRIGGER
OUT
E
MODEL NO.
DTR
-
10.5
GND
C
D
E
B
A
12
V
TRIGGER
OUT
100mA MAX.
100mA MAX.
100mA MAX.
TOTAL
100mA MAX.
200mA MAX.
UDD
AC
INLET
A
L
R
FRONT SURR SURR
BACK
CENTER
SUB
WOOFER
SUB
WOOFER
FRONT
L
CENTERFRONT
R
SURR BACK
L
(
ASSIGNABLE
)
SURR
R
SURR
L
FRONT
R
(
BTL
)
FRONT
L
(
BTL
)
PRE
OUT
A
(
SINGLE
)
PRE
OUT B
AC 120V 60Hz
SWITCHED
120W 1A MAX.
AC
OUTLET
SPEAKERS A
SPEAKERS B
22
1
66
55
44
33
22
11
OPTICAL COAXIAL
AUDIO IN
1
3
2
1
PH
2
3
9
8
7
6
5
4
4
5
RL
LR
LR
R L
G
IN
1
IN
2
HDMI
S
VIDEO VIDEO
IN IN
IN
1
IN
2
3
2
1
Y
PB
PR
COMPONENT
VIDEO
IN
3
6
5
4
Y
P
B
PR
2
1
4
3
ANTENNA
FM
75
B
SURR BACK
R
(
ASSIGNABLE
)
DIGITAL IN DIGITAL IN
LR
S VIDEOS VIDEO VIDEOVIDEO
CD
OUT
OUT
F
L
OUT
IH
OUT OUT
J
K
OUT
1
AM
1
SBR SBL
SR SL
SUB C
FR FL
SBR SBL
SR SL
SUB C
FR
FL
MULTI
-
CH
IN
1
MULTI
-
CH
IN
2
B
OUT
Y
P
B
P
R
Y
P
B
P
R
COMPONENT VIDEO
IN
(
HD/BNC
)
ETHERNET
(
Net
-
Tune
)
Network Audio server
LAN port
LAN port
WAN port
Internet radio
Modem
Router
LAN/
Ethernet
port/
DTR-10.5
Internet radio
WAN port
Router
LAN port
LAN port
LAN port
Modem
Room 1
Room 2
LAN/
Ethernet
port/
Network Audio server

Table of Contents

Other manuals for Integra DTR-10.5

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Integra DTR-10.5 and is the answer not in the manual?

Integra DTR-10.5 Specifications

Amplifier Specifications IconAmplifier Specifications
amplifier power output at 6 ohms200 W per channel
amplifier power output at 8 ohms150 W per channel
dynamic power output at 3 ohms2 x 340 W
dynamic power output at 4 ohms2 x 260 W
dynamic power output at 8 ohms2 x 175 W
frequency response5 Hz to 100 kHz
signal-to-noise ratio110 dB
total harmonic distortion0.08%
damping factor60 at 8 ohms
Input and Output Specifications IconInput and Output Specifications
line input sensitivity and impedance200 mV, 50 k ohms
multi-channel input sensitivity and impedance200 mV, 50 k ohms
subwoofer input sensitivity and impedance36 mV, 50 k ohms
rec out level and impedance200 mV, 470 ohms
pre out level and impedance1 V, 470 ohms
zone 2/3 line output level and impedance100 mV, 470 ohms
Radio Specifications IconRadio Specifications
AM tuning range530–1, 710 kHz
AM usable sensitivity30 µV
FM tuning range87.5–108.0 MHz
FM usable sensitivity, stereo17.2 dBf, 2.0 µV (75 ohms IHF)
Phono and Tone Control IconPhono and Tone Control
phono input sensitivity2.5 mV, 50 k ohms
phono overload70 mV RMS at 1 kHz, 0.5% THD
RIAA deviation20 Hz to 20 kHz: ±0.8 dB
phono signal-to-noise ratio80 dB
bass control±12 dB at 50 Hz
mid range control±12 dB at 1, 000 Hz
treble control±12 dB at 20, 000 Hz
General Specifications IconGeneral Specifications
power supplyAC 120 V, 60 Hz
power consumption13.0 A
dimensions435 x 175 x 429 mm
weight32.1 kg

Related product manuals