99
Setup Menu
Listening Mode Setup
This menu allows you to configure the listening mode
settings including audio effect and playback options.
This sub-menu allows you to configure the audio effect
and playback options when you play a source in the
Mono listening mode.
a. Re-EQ/Academy
This option allows you to configure whether the Re-EQ
or Academy effect is applied or not. Use these effects
when you do not want to overemphasize the treble
sound. This option can also be set for Zone 2.
Off (Default):
The effects are not applied.
Re-EQ On:
Adjusts the soundtrack in which the treble
is overemphasized, so that the sound is optimized for
home theater.
Academy On:
Lowers the treble level and filters the
noise when the source contains emphasized treble
sound and too much hiss, such as an old mono audio
movie recorded onto videotape.
b. Input Channel
This option configures the output method when you
play the stereo input source in the Mono listening mode.
This option can also be set for Zone 2.
Auto L+R (Default) :
The same audio signals are
output from the left and right speakers.
Left:
When you play an input source with different
languages recorded on each channel, the left channel is
output from the left and right speakers.
Right:
When you play an input source where different
languages are recorded on each channel, the right
channel is output from the left and right speakers.
c. Output Speaker
This option configures the speakers to use when playing
the source in the Mono listening mode. Select the
speaker terminals to which the speakers you want to use
are connected.
Center A (Default) :
Outputs the source only from the
speaker connected to the CENTER SPEAKERS A
terminal.
Center B:
Outputs the source only from the speaker
connected to the CENTER SPEAKERS B terminal.
Center A+B:
Outputs the source from the speakers
connected to the CENTER SPEAKERS A and
CENTER SPEAKERS B terminals.
Front L/R A:
Outputs the source from the speakers
connected to the FRONT L/R SPEAKERS A terminals.
Front L/R B:
Outputs the source from the speakers
connected to the FRONT L/R SPEAKERS B terminals.
Front L/R A+B:
Outputs the source from the speakers
connected to the FRONT L/R SPEAKERS A and
FRONT L/R SPEAKERS B terminals. Note that this
option is not available when the front speakers are in Bi-
amp or in BTL configuration.
• When the “(Speaker B) Front L/R” is set to an option
other than “Main A” in the Speaker Configuration
sub-menu, the available options will be “Center A,”
“Center B,” “Center A+B,” and “Front L/R A.”
• When the “(Speaker A) Center” is set to “Not Used” in
the Speaker Configuration sub-menu, the available
options will be “Front L/R A,” “Front L/R B,” and
“Front L/R A+B.” In this case, the default setting is
“Front L/R A.”
• When the “(Speaker B) Center” is set to an option
other than “Main A” in the Speaker Configuration
sub-menu, the available options will be “Center A,”
“Front L/R A,” “Front L/R B,” and “Front L/R A+B.”
• When the impedance setting for either “Front L/R A”
or “Front L/R B” in the Speaker Impedance sub-menu
is set to “6 ohms” or “4 ohms,” “Front L/R A+B”
cannot be selected. Similarly, when the impedance
setting for either “Center A” or “Center B” in the
Speaker Impedance sub-menu is set to “6 ohms” or “4
ohms,” “Center A+B” cannot be selected.
• When the “(Speaker A) Center” is set to “Not Used”
and the “(Speaker B) Front L/R” is set to an option
other than “Main A” in the Speaker Configuration
sub-menu, this setting will not be displayed.
d. Subwoofer
This option configures the subwoofer to use when playing
the source in the Mono listening mode. Select the terminal to
which the subwoofer you want to use is connected. This
setting can be made when the “(Speaker A) Subwoofer” is
set to an option other than “Not Used” in the Speaker
Configuration sub-menu. However, when the “(Speaker B)
Subwoofer” is set to an option other than “Main A” in the
Speaker Configuration sub-menu, the available options will
be “A” or “Not Used.”
A (Default):
Outputs the source only from the
subwoofer connected to the SUBWOOFER PRE OUT
A terminal.
B:
Outputs the source only from the subwoofer
connected to the SUBWOOFER PRE OUT B terminal.
A+B:
Outputs the source from the subwoofers
connected to SUBWOOFER PRE OUT A and
SUBWOOFER PRE OUT B terminals.
Not Used:
No subwoofers are used for playback.
This sub-menu allows you to configure the audio effect
and playback options when you play a source in the
D.F. Multiplex listening mode.
a. Re-EQ/Academy
This option allows you to configure whether the Re-EQ
or Academy effect is applied or not. Use these effects
when you do not want to overemphasize the treble
sound. This option can also be set for Zone 2.
Off (Default):
The effects are not applied.
Mono Setup Sub-menu
Multiplex Setup Sub-menu
To Next Page
Loading...
Need help?
Amplifier Specifications
