121
Setup Menu
Network Setup
This menu appears when the ETHERNET terminal board [B] (for Net Audio) is inserted.
If using a broadband router (DHCP function), you need not perform “7. Network Setup” because the DHCP function
on the DTR-10.5 is defaulted to “Enable.” When the DHCP function for the broadband router is set to “Disable,”
network setup is required. In this case, you have to be knowledgeable about the network.
DHCP (Dynamic Host Configuration Protocol) and Auto IP
are the mechanisms that automatically perform network
settings such as IP address on a network device such as the DTR-10.5, a PC, and a broadband router.
DNS (Domain Name System)
is the mechanism that converts a domain name, such as “www.integrahometheater.com”
used to browse a homepage, to an IP address such as “210.199.170.69” used in actual communications.
a. DHCP Settings
Specify whether or not to set DHCP automatically.
Enable (Default):
Enables the DHCP function.
Disable:
Disables the DHCP function.
b. IP Address
Specify if “Disable” is selected in “a. DHCP Settings.”
When an xDSL modem or a terminal adapter is
connected directly to the DTR-10.5, enter the IP address
provided by your ISP. The IP address to be entered must
be in the following format. You cannot use the net audio
function with an IP address that is not in the following
format.
CLASS A:
10.0.0.0–10.255.255.255
CLASS B:
172.16.0.0–172.31.255.255
CLASS C:
192.168.0.0–192.168.255.255
c. SUBNET Mask
Specify if “Disable” is selected in “a. DHCP Settings.”
When an xDSL modem or a terminal adapter is
connected directly to the DTR-10.5, enter the subnet
mask provided by your ISP. The subnet mask is usually
“255.255.255.0.”
d. Gateway
Specify if “Disable” is selected in “a. DHCP Settings.”
When an xDSL modem or a terminal adapter is
connected directly to the DTR-10.5, enter the gateway
address provided by your ISP.
e. DNS Server 1, DNS Server 2
Specify if “Disable” is selected in “a. DHCP Settings.”
When an xDSL modem or a terminal adapter is
connected directly to the DTR-10.5, enter the DNS
address provided by your ISP. If connected to a gateway
(router), enter the IP address of the gateway.
When you are informed of a single DNS address, enter
the address into “e. 1st.” If informed of two or more,
enter one into “f. 2nd.”
Specify when connecting to the Internet via a proxy
server.
a. Proxy Server
Some ISPs (Internet service providers) use a proxy
server to connect to the Internet. In this case, follow the
written instructions from the provider to set the proxy.
Enable:
Enables the proxy server function.
Disable (Default):
Disables the proxy server function.
b. Proxy URL Input
Enter the domain name of the proxy server. When
“Disable” is set for “a. Proxy Server,” selecting this
item and pressing the [Enter] button will put the
DTR-10.5 into the character entry mode. Press the [ ]/
[ ]/[ ]/[ ] buttons to select numerics, and then
press the [Enter] button. When all numerics are entered,
exit from the character entry mode.
c. Proxy Port
Enter the port No. of the proxy server. When “Disable”
is set for “a. Proxy Server,” selecting this item and
pressing the [Enter] button will put the DTR-10.5 into
the character entry mode. Press the [ ]/[ ]/[ ]/[ ]
buttons to select numerics, and then press the [Enter]
button. When all numerics are entered, exit from the
character entry mode.
Note:
When the settings are complete, press the [Return]
button to return to the Network Setup menu. Use the
[ ]/[ ] buttons to select “
→
Save Settings,” and then
press the [ ] button to save settings. After setting,
saving data will take a few seconds. While saving data,
be sure not to turn off the power, otherwise the data will
be lost.
a. MAC Address
Confirm the MAC address of your PC. You cannot
change the MAC address.
IP Address Sub-menu
Proxy Sub-menu
MAC
Address Sub-menu
To Next Page
Loading...
Need help?
Amplifier Specifications
