EasyManuals Logo
Home>Intex>Swimming Pool Pump>SF90110T

Intex SF90110T User Manual

Intex SF90110T
23 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #20 background imageLoading...
Page #20 background image
193
PO
SAVE THESE INSTRUCTIONS
(193PO) MODEL SF90110T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/21/2013
English
Page 20
TROUBLESHOOTING GUIDE
TROUBLE CAUSE SOLUTION
• Linecordmustbepluggedintoa3wireoutlet
thatisprotectedbyaClassAGroundFault
Circuit Interrupter, or RCD.
• Resetcircuitbreaker.Ifcircuitbreakertrips
repeatedly, your electrical system may have a
defect. Turn off circuit breaker and call an
electrician to correct the problem.
• Letthemotorcooldownandrestartagain.
• AdjustthechlorineandpHlevel.Consultyourlocal
swimming pool supply stores.
• Loadwithfiltersand,see“sandloadinginstructions”.
• Setvalveto“FILTER”position.
• Operatethefilterforlongerperiods.
• Cleanthestrainerscreenattheinlet.
• Clearanyobstructionsintheintakehosebydischargingit
inside pool wall.
• Tightenhosenuts,checkhosesfordamage,checkpool
water level.
• Backwashfilter.
• Installthenozzleattheupperpositionofthepoolinlet,and
the strainer at the lower position of the pool outlet.
• Removeabout1”ofsandifnecessary.
• Removeanypoolvacuumingdeviceattachedtothe
system line.
• Turnoffpump,clearanydebrisorobstructionintheoutlet,
remove all air from the filter pump and turn pump on again.
• Turnoffpump,ifwaterleakingfromthevacuumrelease
valve, then release valve needs to be replaced. Contact
Intex Service Center immediately to order replacement.
Youmaycoverreleasevalvewiththecaptemporarilyif
you ensure that the strainer cover / strainer grid is installed
and you Do Not run the pump while pool is occupied.
• Fillpooltocorrectwaterlevel.
• Cleanstrainerscreensatpoolinlet.
• Tightenhosenuts,checkhosefordamage.
• ContactIntexservicecenter.
• Remove6-wayvalvecoverandensurethe
o-ring is in place.
• Cleansandtanko-ringwithgardenhosewater.
• Tightentheclampwithwrenchsupplied.
• ContactIntexservicecenter.
• Tighten/reinstallhosenut.
• Ensureo-ring/L-shapeo-ringisinplaceand
not damaged.
• Turnoffthepumpandrestart5minuteslater.
• Re-setthetimer.
• ContactIntexservicecenter.
• Clearanyobstructionsintheintakeby
unscrewing it from the 6-way valve.
• ContactIntexservicecenter.
• UseonlyNo.20silicasandwithparticlesize
range 0.45 to 0.85 mm (0.018 to 0.033 inches)
and a Uniformity Coefficient less than 1.75.
• Changesand.
FILTER MOTOR
FAILS TO START
FILTERDOESN’T
CLEANPOOL
FILTERDOESN’T
PUMP WATER OR
FLOWISVERY
SLOW
PUMPDOESN’T
WORK
6-WAYVALVE/
COVERLEAKING
HOSELEAKING
TIMER IS
INACCURATEOR
TIMERCAN'TBESET
PRESSUREGAUGE
DOESN’TWORK
SANDISFLOWING
BACKINTOTHE
POOL
• Themotorisnotpluggedin.
• TheGFCI/RCDcircuitbreakeris
tripped.
• Motortoohotandoverload
protection is shut off.
• ImproperchlorineorpHlevels.
• Nofilteringmediaintank.
• Wrong6-wayvalvesettingposition.
• Excessivelydirtypool.
• Thestrainerscreenisrestricting
the water flow.
• Cloggedinletordischarge.
• Anairleakontheintakeline.
• Excessivelydirtypool.
• Sandmediacloggedwithdirt.
• Nozzleandstrainerconnections
are reversed.
• Crustingorcakingonthefiltering
sand surface.
• Poolvacuumingdeviceattached
to the system.
• Thevacuumreleasevalveonthe
plunger valve is activated.
• Thevacuumreleasevalveonthe
plunger valve is leaking.
• Lowwaterlevel.
• Strainerscreencloggedup.
• Anairleakontheintakehose.
• Faultymotorortheimpellerisjammed.
• Sandtanko-ringmissing.
• Sandtanko-ringdirty.
• Flangeclampnottight.
• 6-wayvalvedamage.
• Hosenutnotsecurelytight.
• Hoseconnectionfitting
o-ring/L-shape o-ring missing.
• Possibleinnertimerdefective.
• Cloggedinletofthepressure
gauge.
• Pressuregaugedamage.
• Sandistoosmall.
• Sandbediscalcified.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Intex SF90110T and is the answer not in the manual?

Intex SF90110T Specifications

General IconGeneral
BrandIntex
ModelSF90110T
CategorySwimming Pool Pump
LanguageEnglish

Related product manuals