Iseki TM3245 User Manual (English)

Other manuals for Iseki TM3245

Questions and Answers:

J
jarvisdavidAug 12, 2025
What to do if the starter motor of my Iseki TM3245 doesn't operate when the key is turned to START?
- K
  Kevin WilsonAug 12, 2025
  If the starter motor doesn't operate when you turn the key to START, there are several possible causes: * Ensure the gear shift lever is in neutral; if not, place it in neutral. * Make sure the PTO switch is off; if it's on, turn it off. * Check the battery. If it's discharged, charge it. * Inspect the terminals for looseness or dirt; clean and retighten them securely.
J
Jennifer BoothAug 16, 2025
Why is the starter motor on my Iseki TM3245 operating but not at full speed?
- C
  Charles BeckAug 16, 2025
  If the starter motor operates but not at full speed, it could be due to: * A discharged battery; charge the battery. * Loose or dirty terminals; clean and retighten them securely. * A defective ground; clean and tighten the starter mounting. * Improper oil viscosity; replace with oil of proper viscosity.
A
andrewrobbinsAug 19, 2025
What to do if my Iseki Tractor engine is running irregularly?
- A
  ashley68Aug 19, 2025
  If your engine is running irregularly, consider the following: * There might be air in the fuel system; air-bleed the fuel system. * The fuel filter may be clogged; clean the filter. * The fuel line could be leaking air; retighten clamps or replace defective pipes.
D
David WaltersAug 23, 2025
What to do if the starter motor operates but not at full speed in my Iseki Tractor?
- G
  Gabriel EspinozaAug 23, 2025
  If the starter motor of your Iseki Tractor operates but not at full speed, it could be due to a discharged battery, loose or dirty terminals, a defective ground, improper oil viscosity or a defective engine. Try charging the battery and cleaning and retightening the terminals securely. Also, clean and tighten the starter mounting, or replace the oil with proper viscosity.
P
Patrick LawrenceAug 27, 2025
Why is the oil pressure monitor lit on my Iseki TM3245 Tractor?
- S
  Steven BlackwellAug 27, 2025
  If the oil pressure monitor is lit during operation of your Iseki Tractor, it may be caused by insufficient engine oil, oil that is too low in viscosity, a defective pressure switch, a clogged oil filter, or a defective oil pump. Replenish the oil, replace it with oil of proper viscosity, replace the pressure switch, or replace the element cartridge.
K
Kristin JacksonAug 31, 2025
What to do if the starter motor operates but engine doesn't start on my Iseki Tractor?
- C
  Claudia StanleyAug 31, 2025
  If the starter motor of your Iseki Tractor operates but the engine does not start, it could be due to the electric fuel control not operating, air in the fuel system, a clogged fuel filter, fuel not being supplied, an incorrect preheating procedure, or a defective engine. Try air-bleeding the fuel system, cleaning the fuel filter, checking the fuel level and opening the fuel valve, or increasing the use of glow plugs.
P
Phillip FoxSep 4, 2025
Why are the exhaust fumes white on my Iseki TM3245 Tractor?
- D
  Deanna PeckSep 4, 2025
  If the exhaust fumes from your Iseki Tractor are white, it could be due to a clogged air cleaner, high engine oil level, insufficient fuel delivery, or a cold-running engine. Try cleaning or replacing the air cleaner element(s), inspecting the oil level and correcting it, or allowing the engine to warm up and checking the thermostat.
B
Brett CrawfordSep 7, 2025
What to do if the starter motor of my Iseki Tractor operates but the engine does not start?
- A
  angela13Sep 7, 2025
  If the starter motor operates but the engine doesn't start, consider these possibilities: * Check the fuel level and ensure the fuel valve is open, as fuel may not be supplied. * Air might be in the fuel system; in this case, air-bleed the fuel system. * The fuel filter might be clogged; try cleaning it. * Ensure you are using the correct preheating procedure and increase use of glow plugs if needed.

Iseki TM3245 Specifications

General

Engine Type	Diesel
Engine Power	24 hp
Cylinders	3
Drive	4WD
PTO Speed	540
Tire Size Front	6.00-12

Summary

TO OUR CUSTOMER

Safety Instructions

Provides essential items to observe while operating the tractor.

Technical Instructions

Provides items necessary to operate, adjust and service the tractor.

SAFETY

Personal Safety Instructions

Explains safety words and symbols used in the manual and on decals.

Making Your Tractor a Safe Vehicle

Instructions on how to maintain safety, including modifications and road use.

Before Operation

Pre-operation checks and procedures to ensure safe operation.

During Operation

Safety guidelines and precautions during tractor operation.

Inspection and Maintenance

Safety procedures and precautions for inspection and maintenance.

Safety Decals

Identifies and explains various safety decals on the tractor.

TRACTOR IDENTIFICATION

Statutory Plate

Information on the statutory plate with tractor identification details.

Model / Serial Number

Guides on identifying tractor, engine, and chassis model/serial numbers.

INSTRUMENTS & CONTROLS

Instrument Panel and Switches

Details the layout and function of the instrument panel and its switches.

Indicator Light Strip

Explains the function of various indicator lights on the strip.

Transmission Shift Levers

Explains the gear shift levers for mechanical and hydrostatic transmissions.

Seat & Suspension Adjustment

Guides on adjusting the tractor seat and suspension settings.

OPERATION

Break-in Period

Guidelines for the initial 50-hour break-in period for the tractor.

Starting

Procedures for starting the tractor.

Ground Speed Selection

How to select ground speeds for mechanical transmission.

Stopping Tractor

Procedures for stopping the tractor with mechanical and hydrostatic transmissions.

Power Take-Off (PTO)

Important safety points and procedures for PTO operation.

3-Point Hitch

Details on attaching, detaching, and operating the 3-point hitch system.

Roll Over Protective Structure (ROPS)

Information and safety precautions for ROPS installation and use.

Jacking

Safety procedures and instructions for jacking the tractor.

LUBRICATION & PERIODIC MAINTENANCE

Specifications & Capacities

Details fluid capacities and specifications for tractor components.

Periodic Inspection and Maintenance Table

A comprehensive maintenance schedule based on operating hours.

Service Access

Procedures for accessing service points like the engine hood, panels, and grille.

Engine Oil & Filter

Procedures for checking and changing engine oil and filter.

Cooling System

Maintenance and service procedures for the tractor's cooling system.

Fuel System

Information on using clean diesel fuel and maintaining the fuel system.

ELECTRICAL SYSTEM

Battery

Information on battery location, maintenance, and handling precautions.

Starting Switches

Details on the neutral-start system and starting requirements.

Brake Free-Play Adjustment

How to check and adjust the brake pedal free-play.

WHEELS & TIRES

Tire Inflation Pressures

Importance of correct tire pressure and replacement guidelines.

Steering Free-Play

Checking and correcting excessive free-play in the steering system.

TROUBLESHOOTING

Engine

Common engine problems, their possible causes, and remedies.

Hydraulic System

Troubleshooting for hydraulic system problems like low pressure or leaks.

Electrical System

Troubleshooting for electrical system faults like battery not charging or dim lights.

SPECIFICATIONS

Mechanical Transmission

Technical specifications for mechanical transmission models.

Hydrostatic Transmission

Technical specifications for hydrostatic transmission models.

Dimensions

Overall dimensions of the tractor with different ROPS types.

Dimensional Limits of Implements

Maximum dimensions and weights for various tractor implements.

Noise Declaration

Declared driver perceived sound levels and sound test results.

Related product manuals