Name: ITech IT6005C-80-150
Brand: ITech
Rating: 5 (1 reviews)

To Next Page

To Previous Page

Power Supply Function

TEST-10

This test is intended to check the correct reinitialisation of the component after

interruption of onboard power supply. This test shall only be performed on

DUT's whose control logic (or parts thereof) is supplied by 48 V.

The waveform is as follows:

138

Warranty3
Limitation of Warranty3
Safety Symbols4
Safety Precautions4
Environmental Conditions6
Regulation Tag7
Waste Electrical and Electronic Equipment (WEEE) Directive8
Compliance Information9
Table of Contents10
Quick Reference13
Brief Introduction13
Front-Panel Overview16
Keyboard Introduction16
Push-On Knob19
Rear Panel Introduction19
VFD Indicator Lamps Description21
Configuration Menu Function22
System Menu Function23
Options Introduction28
Inspection and Installation31
Unpacking and Transportation31
Verifying the Shipment34
Instrument Size Introduction35
Connecting the Power Cord36
Connecting the Device under Test (DUT)42
Remote Interface Connection48
USB Interface48
LAN Interface49
CAN Interface54
GPIB Interface (Optional)55
Interface (Optional)56
Getting Started59
Power-On Self-Test59
Set Output Value63
Use the Front Panel Menu64
On/Off Control65
Power Supply Function66
Set the Output Voltage66
Set the Output Current66
Set the Output Power67
Config Menu for Power Supply67
Set the CC/CV Priority Mode67
Set the Internal Resistance71
CR Function in Sink Mode72
Set the Output-On/Output-Off Delay73
Protection Function for Power Supply73
Set Over-Voltage Protection (OVP)76
Set Over-Current Protection (OCP)77
Set Over-Power Protection (OPP)78
Set Under-Current Protection (UCP)79
Set Under-Voltage Protection (UVP)80
Over-Temperature Protection (OTP)80
Sense Reverse Protection81
Function Menu for Power Supply82
LIST Function82
Battery Charging/Discharging Test Function93
Built-In Waveform Function96
Solar Photovoltaic Curve Simulation Function (SAS)153
Battery Simulation Function158
Basic Operation163
Local/Remote Mode Switch163
Key Lock Function163
Save and Recall Operations164
Save Operation165
Recall Operation165
Data Logging Function165
Set the Beeper Status (Beep)168
Set the Power-On State (Poweron)169
Sense Function (Sense)170
Select Trigger Source (Trig Source)171
Set the Communication Information (I/O Con)172
Set Parallel Operation Mode (Parallel)173
Digital I/O Function (Digital Port)177
IO-1. Ps-Clear, Not-Invert181
IO-2. Ps, Not-Invert183
IO-3. Off-Status, Not-Invert184
IO-4. Ext-Trig, Not-Invert186
IO-5. INH-Living, Not-Invert189
IO-6. Sync-On, Not-Invert192
IO-7. Sync-Off, Not-Invert194
Analogue Function (Ext-Program) (Optional)196
Restored to Factory Setting (System Reset)201
View the System Information (System Info)203
System Upgrade204
Technical Specification208
Main Specification208
197209
It6005C-80-150209
It6010C-80-300211
It6015C-80-450213
204216
It6006C-300-75216
It6012C-300-150218
It6018C-300-225220
210222
It6006C-500-40222
It6012C-500-80225
It6018C-500-120227
217229
It6006C-800-25229
It6012C-800-50231
It6018C-800-75233
1500V236
It6018C-1500-40236
2250V238
It6018C-2250-25238
Supplemental Characteristics241
Routine Maintenance242
Instrument Self-Test242
Cleaning and Maintenance242
Contact of ITECH Engineers243
Return for Repair244
A Appendix246
Specifications of Red and Black Test Cables246
Troubleshooting247
Fuse Replacement249

ITech IT6005C-80-150 User Manual

Table of Contents

Questions and Answers:

ITech IT6005C-80-150 Specifications

Related product manuals

Brand	ITech
Model	IT6005C-80-150
Category	Power Supply
Language	English