Why is my Janome Sewing Machine skipping stitches?
If your Janome Sewing Machine is skipping stitches, there are a few things to check. Ensure you're using the correct needle and that it's properly inserted (refer to page 10). Also, the needle could be bent or blunt (refer to page 10). Finally, the machine might not be threaded correctly, or the thread could be tangled (refer to pages 19-32).
Why does the thread keep breaking on my Janome Sewing Machine?
If the thread keeps breaking on your Janome Sewing Machine, consider these possibilities. The machine might not be threaded correctly, or the thread could be tangled, so refer to pages 19-32. Also, the thread tension may be too tight, in which case, consult pages 37-41 and 45. Ensure you're using the correct needle and that it's properly inserted; see page 10. The needle could be bent or blunt, so check page 10. Finally, using a poor-quality thread could also cause breakage, so refer to page 15.
Why is the needle breaking on my Janome Sewing Machine?
If the needle on your Janome Sewing Machine is breaking, it could be due to several reasons. You might be using the wrong needle or it might be incorrectly inserted, so refer to page 10. The needle could also be bent or worn, so consult page 10. Avoid forcibly pulling the fabric; instead, pull it lightly.
What to do if fabric is not being fed smoothly on my Janome Air Thread 2000D Professional Sewing Machine?
If the fabric isn't feeding smoothly through your Janome Sewing Machine, check these potential causes: * Make sure the presser foot is lowered. * The foot pressure might be too low (refer to page 10). * The feed dog could be packed with lint (refer to page 52).
Why is my Janome Sewing Machine causing seam puckering?
If you're experiencing seam puckering with your Janome Sewing Machine, here are some possible reasons: * The thread tension might be too tight (refer to pages 37-41 and 45). * The machine might not be threaded correctly, or the thread could be tangled (refer to pages 19-32). * The stitch length dial and/or the differential feed dial might not be adjusted correctly (refer to pages 33, 42, 46-49). * The chaining finger might not be set correctly (refer to page 13).
Why does the fabric curl when using my Janome Air Thread 2000D Professional Sewing Machine?
If the fabric is curling when using your Janome Sewing Machine, it could be due to a couple of reasons: the upper looper thread tension or the lower looper thread tension might be too tight, so refer to pages 38-41 and 45. Also, the chaining finger might not be set correctly, so refer to page 13.
What causes the fabric to not cut neatly on my Janome Air Thread 2000D Professional?
If the fabric isn't being cut neatly by your Janome Sewing Machine, it could be because the upper knife is deactivated (refer to page 12) or the upper knife is dull (refer to page 54).
Why is my Janome Air Thread 2000D Professional Sewing Machine needle threader not working?
If the needle threader isn't working on your Janome Sewing Machine, it could be due to these reasons: * The “o” mark on the belt cover might not be aligned with the “-” mark on the handwheel (refer to page 30). * The needle threader switch lever might not be set correctly (refer to page 30). * The needle threader might not be used correctly (refer to page 30).
General| Type | Overlocker |
|---|---|
| Air Threading System | Yes |
| Maximum Sewing Speed | 1300 spm |
| Needle Type | HAx1SP |
| Stitches | Rolled Hem, Flatlock |
| Presser Feet | Standard |
| Threads | 2/3/4 thread |
| Stitch Options | Rolled hem, flatlock |
Instructions to reduce the risk of electric shock when using the machine.
General warnings for safe operation and preventing injury from burns, fire, or electric shock.
Lists and identifies the main components of the sewing machine.
Instructions on how to connect the machine to the power source.
Initial preparation steps before operating the machine for the first time.
How to control the speed of the sewing machine using the foot control.
Information on the function and correct use of the handwheel.
Instructions for opening and closing the looper and side covers.
Using the presser foot lifter and attaching/removing the presser foot.
Explanation of the guide lines on the presser foot for alignment.
How to adjust the presser foot pressure for different fabrics.
Detailed instructions for replacing the sewing machine needle.
Method to check if the needle is in good condition.
How to adjust the length of the stitches.
How to adjust the differential feed ratio for fabric stretching or gathering.
Instructions for sewing gathering with the differential feed.
Steps to deactivate or activate the upper knife for specific stitches.
How to adjust the cutting width of the fabric.
Adjusting the chaining finger switch for different sewing types.
Proper positioning of the thread guide bar.
How to attach spool holder caps and nets for thread spools.
Step-by-step guide for threading the machine with four threads.
Adjusting the lower looper pre-tension setting slider.
Instructions for threading the machine with three threads.
Instructions for threading the machine with two threads.
How to use the spreader for two-thread serging.
Detailed steps for threading the lower looper.
Detailed steps for threading the upper looper.
Adjusting looper threader switch and selection levers.
Step-by-step guide for threading the right needle.
Instructions for using the automatic needle threader.
Step-by-step guide for threading the left needle.
Initial steps for beginning a test stitch on the machine.
Steps for completing a sewing operation and finishing the thread chain.
How to continue sewing without interruption.
How to use guide lines for accurate stitching.
Methods to secure thread ends to prevent unraveling.
How to cut seams using the machine's features.
Illustration and explanation of correct thread tension for 4 threads.
General procedure for adjusting thread tension.
Identifying and fixing loose left needle thread tension.
Identifying and fixing loose right needle thread tension.
Illustration and explanation of correct thread tension for 3 threads.
General procedure for adjusting thread tension for 3 threads.
Troubleshooting loose needle thread tension for 3 threads.
Troubleshooting looper thread tension imbalance for 3 threads.
Troubleshooting looper thread tension imbalance for 3 threads.
Illustration and explanation of correct thread tension for 2 threads.
General procedure for adjusting thread tension for 2 threads.
Troubleshooting needle/lower looper thread tension imbalance.
Troubleshooting needle/lower looper thread tension imbalance.
Chart for tension dial and machine settings for hemming types.
Tips for achieving better results with rolled hemming.
How to gently pull fabric for picot edging.
Illustration and explanation of correct thread tension.
General steps to adjust thread tension.
Troubleshooting looper and right needle thread tension for hems.
Troubleshooting loose upper looper thread tension.
Troubleshooting loose lower and tight upper looper thread tension.
Settings and notes for decorative overedging.
How to sew and finish outer corners.
How to sew and finish inner corners.
Instructions for cleaning the upper knife area.
Steps for cleaning the feed dog.
How to clean the looper threader pipe.
Guide on how to replace the upper knife.
Instructions for oiling the sewing machine.
To Next Page