Janome MEMORY CRAFT 4800 User Manual (English)

Questions and Answers:

K
kenneth72Aug 17, 2025
Why does the needle thread keep breaking on my Janome MEMORY CRAFT 4800?
- B
  Brandon RogersAug 18, 2025
  If the needle thread keeps breaking on your Janome Sewing Machine, try the following: First, make sure the needle thread is threaded properly. Then, adjust the needle thread tension. If the problem persists, replace the needle if it is bent or blunt, and ensure it is inserted correctly. Also, make sure both the needle and bobbin threads are drawn to the rear when you start sewing, and draw the fabric to the rear when you finish. Finally, consider changing to a heavier or finer thread suitable for the needle.
L
Lauren AllisonAug 20, 2025
What to do if my Janome MEMORY CRAFT 4800 Sewing Machine is skipping stitches?
- E
  Elizabeth PetersAug 20, 2025
  If your Janome Sewing Machine is skipping stitches, try these solutions: Ensure the needle is inserted correctly and replace it if bent or blunt. Use the correct needle and threads suitable for the fabric. For stretch, very fine fabrics, or synthetics, use a blue tipped needle. Also, thread the needle thread properly and increase the presser foot pressure. Finally, double-check that you are using the correct needle for your project.
Z
zjohnsonAug 23, 2025
Why does the needle keep breaking on my Janome Sewing Machine?
- M
  Morgan HawkinsAug 23, 2025
  If the needle breaks on your Janome Sewing Machine, here's what you can do: First, make sure the needle is inserted correctly. Replace the needle if it is bent or blunt. Tighten the needle clamp screw and adjust the needle thread tension. Remember to draw the fabric to the rear when you finish sewing. Finally, ensure you are using a needle suitable for the fabric you are sewing.
J
Julia PetersonAug 25, 2025
What to do if the bobbin thread breaks on Janome Sewing Machine?
- M
  murrayjohnAug 26, 2025
  If the bobbin thread is breaking on your Janome Sewing Machine, try these steps: Ensure the bobbin thread is threaded properly in the bobbin holder. Clean out any lint in the bobbin holder. If the bobbin is damaged, replace it.
R
Robert EstradaAug 27, 2025
Why is my Janome MEMORY CRAFT 4800 Sewing Machine so noisy?
- T
  Thomas JonesAug 27, 2025
  If your Janome Sewing Machine is operating noisily, try these steps: remove any thread caught in the hook race, and clean any lint built up in the bobbin holder or hook race. Also, clean any lint packed in the feed dogs. A slight humming sound from the internal motor is normal and can be ignored.
K
Kevin ParkerAug 30, 2025
Why is my Janome Sewing Machine not working?
- A
  averyamandaAug 30, 2025
  If your Janome Sewing Machine isn’t working, check these items: First, ensure the machine is plugged in. Then, remove any thread caught in the hook race. Also, move the bobbin winder spindle back to its original position.
H
holly99Sep 1, 2025
How to fix the issue of cloth not feeding smoothly in my Janome Sewing Machine?
- S
  sheppardwalterSep 1, 2025
  If the cloth isn't feeding smoothly through your Janome Sewing Machine, try these solutions: First, clean any lint packed in the feed dog. Increase the presser foot pressure. Change to a coarser stitch. Make sure the feed dogs are raised. Finally, use the correct presser foot for your project.
S
Shawn GlennSep 4, 2025
Why is my Janome Sewing Machine causing seam puckering?
- L
  Lisa EstradaSep 4, 2025
  If you're experiencing seam puckering with your Janome Sewing Machine, try the following: Decrease the needle thread tension. Ensure the needle thread is threaded properly. Use a lighter needle for the fabric you're sewing and adjust the stitch length to be shorter. Also, make sure the presser foot pressure is correctly adjusted.
S
Susan GutierrezSep 6, 2025
What to do if patterns are distorted on my Janome MEMORY CRAFT 4800?
- W
  wheelerlisaSep 7, 2025
  If the patterns are distorted when using your Janome Sewing Machine, try these solutions: Use the correct presser foot. Adjust the needle thread tension and the stitch length to be suitable for the fabric. Set the feed balancing dial properly. For stretch and very fine fabrics, use interfacing.
A
Alexander MartinSep 9, 2025
How to fix automatic buttonhole stitches that are not working on my Janome MEMORY CRAFT 4800?
- J
  Justin MichaelSep 9, 2025
  If the automatic buttonhole stitches aren't working on your Janome Sewing Machine, try these steps: Adjust the stitch length to be suitable for the fabric. Set the feed balancing dial properly. Use interfacing with stretch fabrics. Ensure you are using the correct presser foot and that the machine is set correctly.

Janome MEMORY CRAFT 4800 Specifications

General

Type	Electronic
Maximum Stitch Width	7mm
Maximum Stitch Length	5mm
Needle Threader	Yes
Speed Control	Yes
Start/Stop Button	Yes
Needle Up/Down	Yes
LCD Screen	Yes
Built-in Memory	Yes
Free Arm	Yes
Buttonholes	7