Jasic TIG Series User Manual (English)

Other manuals for Jasic TIG Series

Questions and Answers:

T
Tabitha LevineSep 14, 2025
Why is the power LED off and the fan not working on my Jasic Welding System?
- C
  careykeithSep 14, 2025
  If the power LED is OFF and the fan is not functioning on your Jasic Welding System, it could be due to several reasons. First, check if the primary supply voltage has been switched ON or if the input fuse has blown; replace the fuse if necessary. Second, ensure the welding power source input switch is switched ON. Finally, check for and secure any loose internal connections.
L
longcynthiaAug 25, 2025
Why does the TIG electrode melt when arc is struck with my Jasic TIG?
- G
  gmillerAug 25, 2025
  If the TIG electrode melts when striking an arc with your Jasic Welding System, it's likely that the TIG torch is connected to the (+) VE terminal. Reconnect the TIG torch to the correct terminal.
R
Robert HoffmanAug 25, 2025
How to fix excessive spatter in MMA welding with Jasic TIG?
- S
  Sherry HallAug 26, 2025
  If you're experiencing excessive spatter during MMA welding with your Jasic Welding System, the output polarity connection may be incorrect. Try exchanging the polarity connection.
C
Crystal FergusonAug 26, 2025
What to do if the Jasic TIG Welding System power LED is OFF and the fan is not functioning?
- C
  christopher00Aug 27, 2025
  If the power LED is off and the fan isn't working on your Jasic Welding System, first ensure the main power supply is switched ON and check/replace the input fuse. Also, verify that the welding power source input switch is ON. Finally, check and secure any loose connections internally.
J
joshualutzAug 27, 2025
Why is there no gas flow when the TIG torch trigger switch is depressed on my Jasic Welding System?
- J
  Jacqueline PatelAug 27, 2025
  If there's no gas flow when you depress the TIG torch trigger switch on your Jasic Welding System, consider the following: * The gas cylinder may be empty, in which case you should replace or refill it. * The gas regulator might be turned off; turn it on. * The gas hose could be blocked or cut; inspect and repair or replace it. * The torch trigger switch lead may be disconnected, or the switch/lead could be faulty; check the connection and functionality.
D
David JohnsonSep 9, 2025
Why is the fault LED on and the fan running on my Jasic Welding System?
- A
  Andrew ParkerSep 9, 2025
  If the fault LED is ON and the fan is running on your Jasic Welding System, it could be due to overheating protection or incorrect mains supply. First, allow the machine to cool down. Second, ensure the incoming mains supply is within 230V +/- 15%.
O
Olivia McdonaldSep 7, 2025
What to do if my Jasic TIG shows error E60 - Overheated?
- T
  Thomas BlackSep 8, 2025
  If your Jasic Welding System displays 'E60 - Overheated', it means the main circuit has been working beyond its duty cycle. To resolve this, leave the machine powered on and allow the main circuit to cool down before resuming welding.
A
Alexander MarksSep 8, 2025
What should I do if my Jasic TIG Welding System displays error E10 - Overcurrent?
- C
  Charles HernandezSep 9, 2025
  If your Jasic Welding System shows error 'E10 - Overcurrent', power off the machine and restart it. If the problem persists, contact the service department for assistance.
R
Robert GonzalezSep 2, 2025
What to do if the fault LED is ON and the fan is running on my Jasic Welding System?
- C
  Cheryl SteeleSep 2, 2025
  If the fault LED is ON and the fan is running on your Jasic Welding System, it could be due to these reasons: * The machine might be under over-heating protection. In this case, it will recover automatically after the welding machine has cooled down. Allow the machine to cool down. * The incoming mains supply might be outside the acceptable voltage range. Check the incoming mains supply to ensure it is within 230V +/- 15%.
T
Thomas GriffinAug 31, 2025
What to do if the Jasic Welding System power LED is OFF and the fan isn't working?
- S
  Sharon HowellAug 31, 2025
  If the power LED is off and the fan isn't running on your Jasic Welding System, it could be due to several reasons: * The primary supply voltage might not be switched ON, or the input fuse may have blown. Ensure the power supply voltage is switched ON and replace the blown input fuse, if necessary. * The welding power source input switch could be switched OFF. Turn ON the welding power source input switch. * There might be loose internal connections. Check and secure any loose internal connections.