JBL ON TIME 200ID - Specifications; Troubleshooting; Sound Quality

SPECIFICATIONS
JBL ON TIME 200lD
TROUBLESHOOTING
SOUND QUALITY
I
Frequency Response: 70Hz - 20kHz
Power Consumption: 30 Watts maximum
JBL On Time 20010 Transducer: Phoenix SE
1-3/4" (45mm) x 2 (full range per channell
Power: 12 Watts per satellite at 1% THO
Input Impedance: >5k Ohms
Signal-to-Noise Ratio: >80dB
Input Sensitivity: 350mV RMS for rated power output
Power (USA/Canada): 120 Volts, 60Hz AC
Power (Europe/UK): 220 - 230 Volts, 50Hz or 60Hz AC
Power (Japan): 100 Volts, 50Hz or 60Hz AC
Power (Australial: 240 Volts, 50Hz or 60Hz AC
UlICUL/CE-Approved
Dimensions: 11-3/16" x 5-3/4" x 2-3/4"
(W x 0 x Hl (284mm x 146mm x 70mm)
Weight: 1.8 Ib (0.8kg)
Remote Battery: CR2025
Symptom
No sound from the
JBL On Time 20010 unit
No sound or weak signal from
the AM/FM radio
Sound comes from one
side/channel only
Oistortion (static, crackling or
hissing sounds)
Possible Problem
No power to the unit
Incorrect source selection
Bad reception from current location
Interference
iPod or audio cable is not seated
properly
Noise may be caused by interference
from a monitor, cell phone or other
transmitting device
JBL On Time 2001D unit is being over-
driven by an amplified audio source
Solution
Make sure the wall power outlet or power strip
has power. Make sure all switches for outlet!
power strip are on and that all switches for speaker
system are on.
Make sure the correct source is selected; choose
FM radio as a source. Turn up the volume. Check
the system with a known good source, such as your
iPod. Connect the Aux In cable to the headphone
jack on your iPod.
Reposition your JBL On Time 2001D unit until you
find better reception.
Check surrounding area for any possible
interference; wrap up any excess cables.
Make sure the iPod or Aux In cable is seated all the
way into the JBL On Time 200ID unit.
Turn monitor off to see whether noise is eliminated.
Move JBL On Time 20010 unit's cables farther away
from monitor.
Make sure the unit is connected to an appropriate
source device. Make sure all signal cables are
inserted snugly into receptacles.
Note
Is the display on? If not,
power is not getting to
your JBL On Time 2001D;
try the solutions shown.
If you are still getting a weak signal
from AM broadcasts, connect the
external AM antenna to the AM
antenna jack.
If you want to use a longer cable,
make sure it's a 3.5mm mini-jack
stereo male-to-male cable
•
DISPOSAL: Do not dispose of this
product as unsorted municipal
waste. Collection of such waste
separately for special treatment is
necessary.
IMPORTANT: Use UM4/AAA/LR03
alkaline-type nonrechargeable
batteries only.
Too much bass or treble
JBL On Time 20010 unit emits a
loud hum or buzzing noise
Speaker system experiences
radio frequency interference
or picks up a radio station
Volume level may be too high
Check the EO setting on your iPod or
source device
Input cables are not plugged in properly
Input cable may be picking up
interference
Check volume of source device; some devices
will distort the output signal if the volume is set to
maximum.
We recommend that the source device EO be set
to Flat or Off.
Check input cable connection.
Wrap up excess input cable to make it as short
as possible.
Purchase aferrite clamp and attach it over the
input cable; a clamp can be purchased at your local
electronics store.
WWW.JBL.COM13