What to do if my JBL Speaker System signal sounds distorted and very loud?
If the signal from your JBL Speaker System sounds distorted and very loud, and the OVERLOAD light is frequently lit, it likely means that the input signal is too high, exceeding what the speakers can handle. To fix this, reduce the output level of the source and lower the level controls on the speaker.
How to fix hum or buzz in JBL Speaker System?
Humming or buzzing sounds in your JBL Speaker System can stem from several factors: * Improper A/C grounding or ground loops. You can try to 'telescope' the audio ground using an XLR/F to XLR/M adapter on one end or re-route the audio cable away from AC power and lighting cables. * Excessively long unbalanced cable runs. To address this, utilize the balanced outputs (if available) of your mixer to drive your speakers. Alternatively, use a DI (direct injection) box to convert your unbalanced equipment output to a balanced output. * Improper system gain structure. Review your system setup and adjust controls as needed, paying attention to input sensitivity (gain).
What to do if my JBL PRX618S-XLF Speaker System turns on but has no sound?
If your JBL Speaker System turns on but produces no sound, the problem may be with faulty cables and connections. Check the VU meters on the source mixer and verify that the CD/MP3 is playing. Use headphones to confirm that the instrument is sending an audio signal. Also, disconnect and re-seat the signal cables and replace any suspected faulty cables with known-good ones.
Why do my JBL PRX618S-XLF howl when I turn up the microphone volume?
If your JBL Speaker System is experiencing feedback and howling when the microphone volume is increased, it could be due to several reasons: * The microphones may be pointed towards the speakers. To resolve this, reposition the speakers so they are not directed at the microphone's pickup pattern. * The equalizer settings might be incorrect. In this case, identify the feedback frequency and lower it using the mixer EQ or an external equalizer. * The gain might be too high. Try reducing the gain on the mixer and move the microphone closer to the sound source.
Why does my JBL PRX618S-XLF Speaker System sound distorted even at moderate volumes?
If your JBL Speaker System sounds distorted even at moderate volumes, and the OVERLOAD light is not lit, the issue might be that the mixer or another source is overdriven (clipping). Review the owner’s manual for your system setup and adjust controls as needed. Specifically, check the input sensitivity (gain) and the gain structure of the signal chain.
Why does the hum or buzz in my JBL PRX618S-XLF Speaker System change when I move the mixer level controls?
If the hum or buzz in your JBL Speaker System increases or decreases when the mixer level controls are adjusted, it could be due to an improper A/C ground or faulty equipment connected to the mixer input. Try disconnecting or muting channels one at a time to identify the source of the problem. Also, a faulty cable between the source equipment and mixer could be the cause; try substituting it with a known-good cable.
How to eliminate noise or hiss from JBL PRX618S-XLF Speaker System output?
If you hear noise or hiss from your JBL Speaker System's output, it may be due to a noisy source device. Disconnect the devices connected to your speaker one at a time. If the noise disappears, the issue lies with the source or its connecting cable.
Why is there no sound when I connect a microphone directly to the MIC input of my JBL PRX618S-XLF?
If you're not getting any sound when connecting a microphone directly to the MIC input on your JBL Speaker System, the microphone may require 48V phantom power, which the PRX600 speakers do not supply. Try switching to a dynamic microphone, using a battery in the microphone (if possible), or using an external phantom power supply. Also, check the cable.
How to reduce excessive low frequencies on JBL PRX618S-XLF?
If you are experiencing too much low frequencies when playing back prerecorded music on your JBL Speaker System, this may be caused by recorded music with excessive low frequencies. Switch the EQ switch to 'flat'.
General| Finish | Black DuraFlex finish |
|---|---|
| Type | Subwoofer |
| Driver Size | 18 in |
| Power Rating | 1000 W |
| Input Connectors | XLR |
| Input Impedance | 10k ohms |
| Amplifier Power Rating | 1000 W |
| Enclosure Material | Birch Plywood |
| Suspension / Mounting | M20 |
| AC Power Input | 100V - 240V |
| Output Connectors | XLR |
Procedure for cleaning and maintaining the PRX600 series speaker systems.
Guidelines for safely mounting PRX600 series speakers on stands or poles.
Essential safety information and procedures for suspending JBL loudspeakers.
Standards and specifications for electromagnetic compatibility and product safety.
Notices regarding CSA certification and FCC compliance for the equipment.
Details on the necessary AC power supply for optimal performance of the PRX600 amplifier.
Instructions for safely powering on the unit and selecting the correct voltage.
Information on operating temperature limits and thermal protection features.
Details on the durable construction and materials used in PRX600 series cabinets.
Select between linear frequency response and enhanced low/high frequencies for audio.
Optimizing system use as a main PA or a stage monitor.
Selects input sensitivity for microphones or line-level sources.
Adjusts the overall sound level output of the speaker.
LED indicators for signal presence and system overload protection.
Controls for powering the unit and selecting country voltage ratings.
Connects AC power and audio cables to the speaker.
Engages high-pass filter for smooth transition between subwoofer and full-range speakers.
Inverts polarity to optimize blend and bass response between subwoofer and main speakers.
Adjusts the overall sound level output of the subwoofer.
Controls for powering the unit and selecting country voltage ratings.
LED indicators for signal/overload and ports for audio and power connections.
Simple system setup connecting sound sources directly to speakers.
Combining satellite speakers with a subwoofer for music playback reinforcement.
System configuration for live performance using main speakers and stage monitors.
Multi-speaker system for large crowds, outdoor events, and high SPL applications.
Explanation of audio signal interconnection types and their characteristics.
To Next Page