EasyManua.ls Logo

Jensen 400 - Features and Specifications

Jensen 400
14 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
POWER Amplifiers
2
Features and Specifications
Your new Jensen Power mobile stereo power amplifier is the amplifier of
choice for the high demands of auto sound reproduction. With its deep-bass
reproduction and plenty of reserve power, low harmonic distortion and neutral
reproduction, the Power series of amplifiers takes Mobile Hi-Fi to new heights.
Like all Jensen products, when it comes to accurate sound reproduction the
Power series takes a back seat to no one. Jensen will bring your Hi-Fi
experience to new heights with the following features:
MOSFET Power Supply
High Current Bi-Polar Output Transistors
Optimized Class B Design Minimizes Distortion and Reduces Idle Current
Easily Drives 2-Ohm Loads
Pass-Thru RCA's
Variable Bass EQ 0 - 12dB @ 45 Hz
12dB / Octave Low Pass and High Pass filters
Variable Input Level 400mV - 5V
Short Circuit, DC-offset and Thermal Overload Protection Circuitry
Diagnostic LED's - Green: Power, Red: Standby / Fault
Power 400 / 760 / 880 / 920
Low Pass Filter 40 - 300 Hz
High Pass Filter 40 - 300 Hz
High Pass / Low Pass / Full Range Selector Switch
Stereo / Mono Mode Switch (Power 400 and 880 only)
2/ 3 / 4 Channel Mode Switch (Power 760 and 920 only))
Power 900 / 1050
Mono Subwoofer Amp
Low Pass Filter 40 - 240 Hz (Power 900)
Low Pass Filter 40 - 150 Hz (Power 1050)
Subsonic Filter 10 - 40 Hz, 12dB / octave (Power 900)
Subsonic Filter 15 - 55 Hz, 12dB / octave (Power 1050)
Remote Input Level Control (Remote Bass Control) w/ 5 Meter Interface
Cable
Specifications
Power 400 / 760 / 880 / 920
Load Impedance: 2 / 4-Ohm
Signal to Noise @ 1 kHz: >100dB (rated power)
Channel Separation @ 1 kHz: >60dB
Frequency Response: 5-60 kHz, -3dB
Input Impedance: 20 kHz, nominal
THD+N @ 5 Watts: 0.02%, 1 kHz, 14.4VD
C
Power 900 / 1050
Signal to Noise @ 120 Hz: >100dB (Rated Power)
Channel Separation Not Applicable
THD+N @ 5 Watts: 0.02%, 125 Hz, 14.4VDC
Power Output
RMS Power Output @ 2% THD+N, 1kHz, 14.4VDC
Power 400
75 x 2 Watts, 4-Ohm
100 x 2 Watts, 2-Ohm
200 x 1 Watts, 4-Ohm Bridged
Power 760
75 x 4 Watts, 4-Ohm
100 x 4 Watts, 2-Ohm
190 x 2 Watts, 4-Ohm Bridged Stereo
Power 880
135 x 2 Watts, 4-Ohm
220 x 2 Watts, 2-Ohm
440 x 1 Watts, 4-Ohm Bridged
Power 900
300 x 1 Watts, 4-Ohm
450 x 1 Watts, 2-Ohm
Power 920
100 x 4 Watts, 4-Ohm
140 x 4 Watts, 2-Ohm
230 x 2 Watts, 4-Ohm Bridged Stereo
Power 1050
350 x 1 Watts, 4-Ohm
525 x 1 Watts, 2-Ohm
Specifications subject to change without notice.

Related product manuals