Jet J-2500 User Manual

6
Introduction
The JET 15-Inch 16-Speed Drill Presses and 20-Inch 12-Speed Drill Presses, Models J-2500, J-2530 and J-2550,
feature rugged cast iron design with ground-steel columns for drilling accuracy in metal, wood, and plastic. The
head casting features a ball bearing spindle assembly, supported by four permanently-lubricated, heavy duty ball
bearings that are mounted in an enclosed quill for extended life.
Specifications
Model J-2500 J-2530 J-2550
Stock Number ................................................ 354400 .............................. 354401 ...............................354402
Model Type .................................................... 15-Inch Floor ..................... 15-Inch Bench....................20-Inch Floor
Drilling Capacity
Cast Iron.................................................... Up to 5/8 In. ....................... Up to 5/8 In. .......................Up to 3/4 In.
Steel .......................................................... Up to 1/2 In. ....................... Up to 1/2 In. .......................Up to 5/8 In.
Drill to Center ................................................. 15 Inches ........................... 15 Inches ...........................20 Inches
Motor
Rating ........................................................ 3/4 hp, 1-Phase ................. 3/4 hp, 1-Phase .................1 hp, 1-Phase
RPM .......................................................... 1725 .................................. 1725 ...................................1725
Voltage............................................115/230V (prewired 115V).......115/230V (prewired 115V) ......115/230V (prewired 115V)
Column Diameter ........................................... 2-7/8 In. ............................. 2-7/8 In...............................3-5/8 In.
Quill
Diameter.................................................... 1-7/8 In. ............................. 1-7/8 In...............................2-1/4 In.
Travel ........................................................ 3-1/8 In. ............................. 3-1/8 In...............................4-3/4 In.
Table
Overall ....................................................... 11-1/2 x 11-1/2 In. ............. 11-1/2 x 11-1/2 In...............18-1/2 x 16-1/2 In.
Working Surface........................................ 9-1/2 x 9-1/2 In. ................. 9-1/2 x 9-1/2 In...................15-1/2 x 13-1/2
Travel ........................................................ 24 In. ................................. 15-1/2 In.............................21-1/2 In.
Base
Size ........................................................... 11 x 19-1/2 In. ................... 10-1/2 x 18 In. ....................22-3/4 x 17-3/4 In.
Working Surface........................................ 7 x 7-1/2 ........................... 8 x 8 ...................................13 x 14-1/2
Chuck Size ..................................................... 5/8-In., Key Chuck ............. 5/8-In., Key Chuck .............5/8-In, Key Chuck
Overall Dimensions
Length ....................................................... 31 In. ................................. 31 In. ..................................33-1/2 In.
Width ......................................................... 13 In. ................................. 13 In. ..................................18-1/2 In.
Height ........................................................ 63 In. ................................. 39-1/2 In. ............................67 In.
Spindle to Table (Max.) .................................. 24 In. ................................. 15-1/2 In.............................24 In.
Spindle to Column (Max.) ............................. 7-1/2 In. ............................. 7-1/2 In...............................10-1/2 In.
Spindle
T o Base ..................................................... 48 ...................................... 24 .......................................43-1/2
T aper ......................................................... MT -2 .................................. MT -2 ..................................MT-3
Number of speeds .................................... 16 ....................................... 16 .......................................12
RPM ......................................................... 200, 290, 350, 430 ............. 200, 290, 350, 430 .............150, 260, 300,
500, 580, 640, 720 500, 580, 640, 720 440, 490, 540,
800, 870, 1440, 1630 800, 870, 1440, 1630 1150, 1550, 1840,
1820, 2380, 2540, 3630 1820, 2380, 2540, 3630 2220, 2950, 4200
Shipping Weight ............................................. 185 pounds........................ 157 pounds ........................321 pounds

Jet J-2500 Specifications

General

Brand	Jet
Model	J-2500
Category	Power Tool
Language	English